GSD2230F01WW General Electric Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Thomas E from Lexington, SC
- Parts Used:
- WD15X10003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Wrench set
water leaking on floor under dishwasher
Laid on floor remove two small bolts with nutdriver,loose water line with wrench,remove other water line with pliers.Remove water inlet valve and replace with new one
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carlon from McRae, AR
- Parts Used:
- WD15X10003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Water would not fill.
Wow, could not have been easier. The suggested repair stated that the water inlet valve was the problem 93% of the time. And, it was spot on. It was the exact same replacement part. And, once installed, it worked like a charm. I have bookmarked this website, and will use it for all future appliance repair. I simply could not be more pleased. It was a breeze. Thanks,
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ELLIS from MADISON, AL
- Parts Used:
- WD15X10003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Wrench (Adjustable)
Water leaking from beneath dishwater
It took no time at all to identify where the water was leaking from. I accessed a parts breakdown illustration of my dishwasher, identified the part, ordered it and three days later my leak was fixed. Hose and water inlet valve assembly was easy to swap out. I estimate I saved myself about $150.00 by doing it myself.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Willcox, AZ
- Parts Used:
- WD19X10032
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Leaking motor seal
Followed easy instructions and completed repair in less than 30 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Port St. Lucie, FL
- Parts Used:
- WD09X10025
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Timer knob just rotated on the timer shaft.
Pull the knob off and look for any special characteristics e.g. location of detents or other devices to index the knob n the shaft. Found an indentical part on on PARTSELECT website. Pictures were sure a big help. Purchased unit and installed in about 3 minutes. NO PROBLEMS.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Leanne from Divide, MT
- Parts Used:
- WD12X10284
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The rinse aid fill cap was stripped.
I removed the old cap and put on the new cap.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- martin from chesterton, IN
- Parts Used:
- WD15X10003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
water inlet valve wore out would not work
got replacement valve from part select and works like new this dish wash er is 24 years old. believe it or not did the job with pair of pliers and screw driver. used pliers to take off clamp and screw driver to take out 2 screws and replaced the valve the same way in reverse
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Nespelem, WA
- Parts Used:
- WD15X10003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Socket set, Wrench (Adjustable)
Wouldn't clean upper rack, not enough water
Checked the water supply to the inlet valve - OK, pulled the filler hose from the outlet side of the valve and checked flow in wash cycle. Results, less than 1/2 gallon. Checked your website, found 94% sucess rate by replacing the valve, so I ordered one. It took about 10 minutes to install with a nut driver, 6" adjustable to connect water supply, and plier to hold outlet clamp open to install it; now we look forward to dirty dishes rather than dumping water into the machine it takes care of itself and we once again get sparkly cups andglasses of the top rack. OU- Rah!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Bradenton, FL
- Parts Used:
- WD12X10284
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Dishes cloudy, spotting
Unscrew old stripped out one and put in new one ..wala!! Easy repair for this old lady...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Corvallis, OR
- Parts Used:
- WD12X10284
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
Old rinse aid fill cap broke off at base
I removed the broken stub of the old fill cap with a screw remover. This was the only part that wasn't easy. The new cap fit fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Harry from Bayside, NY
- Parts Used:
- WD08X10057
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
Small leak at the bottom of dishwasher
Removed existing gasket seal on door. Cleaned really well with a household cleaner around the gasket crease. Installed new gasket seal around door. Started with small notch in the middle of the gasket to center on top and then slowly fastened into door edge and slowly snug around bottom edge where the deal is notched and the the difficult part was to feel the seam again on the bottom to re attach seal after notch from corner. Rupert this on the other side of door.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Havertown, PA
- Parts Used:
- WD15X10003
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Socket set
water was leaking from the inlet valve
the repair would have been much easier but the screws from the old inlet valve did not match the size of the holes on the new valve.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Harry from Croghan, NY
- Parts Used:
- WD16X10011, WD12X324
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Detergent cup cover could not be locked closed prior to washing the dishes.
I removed the plastic inner door liner, removed the timer assembly. Replaced both plastic parts, Detergent cup release arm and dispenser release timer lever. The most difficult part was reassembling the timer lever spring. Long nose pliers made it simple. Works like new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- cliff from knoxville, TN
- Parts Used:
- WD13X10003
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Faulty Dishwasher Door Latch
Had to install a new door latch. The installation itself is really quite simple involving removing (separating) the inner door panel to access the latch assembly. The latch is removed by simple push through one slot with a screw driver and the new unit basically pops in through grooved slots. However, I did find it quite helpful to first (and during) review a YouTube video illustrating the replacement. Although it is largely a simple procedure, for the first-time "installer" there are still a few tricky nuances to be aware of.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Betty from Flintstone, GA
- Parts Used:
- WD13X10003
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Door latch would not lock dishwasher door
I unscrewed the front of the door almost to the bottom hinges and removed the latch. Went on line and ordered a replacement. The replacement arrived in a couple days (yeh), was identical to the one I had removed. I could have used another hand but went ahead and replaced it myself. It worked perfectly and I screwed everything back in place. I'm a 73-year-old female, good at taking things apart but not always good at putting them back together but will try anything. Was elated that I could repair it and it actually worked. Great service from your company!
Was this instruction helpful to you?
Thank you for voting!