GSD2000Z07AD General Electric Dishwasher - Instructions

Your video doesn't include disconnecting water supply disconnecting electrical and disconnecting drain hose but after all that the repair to change the solenoid was a easy task but the problem was not solved so I TRIED . thanks Robert

This was one of those wonderful repairs where anything went right.
The part arrived overnight as ordered and even though I was abit leary of it fitting, since it was described as a replacement/new design, it fit perfectly! As mentioned in another post here, draining the water out of the unit so I could tip it over to do the replacement was the hardest part!
I'm sure I saved over $100 doing it myself. Thanks PartSelect!

I Just Open Door And Put Fill Cap In And Turn That It

Used Phillips screwdriver to undo brackets that keep dishwasher in place. Pulled out dishwasher from underneath the counter. Placed hinge arm in spring, hooked spring onto clip, placed hinge arm in clip. Put back dishwasher under the counter and screwed in place. Took all of 15 minutes. Saved 185.00 for service call.

A no brainer, replaced old fill cap with new fill cap. Delighted I was able to order the part, website is user friendly.

Nut driver and philips screwdriver.

after I let the unit rest on its side to expose the bottom part, I took a picture just in case for reference; I marked all electrical connections, so it would go to right place into the new unit; removed the old pump unit by loosening the rubber clamps, for the inlet and outlet; detached the support sling for the motor unit; installed the new pump unit; it fits like a charm and it was wonderful; I had some bad experiences of replacement parts from other suppliers, on many things that I fix , that won't really fit like the original, but this one fits like a charm; I made my first test run with just water with out the detergent and after one cycle I used the necessary dishwasher detergent and it works just like brand new; Thank you, PartSelect, I will be ordering any of my part needs from you. - G.V.

Checked availability of replacement machine and replacement parts online..in this process, I ran across a similar story by someone who fixed similar problem on a similar machine. Before removing the fill valve, I tried to confirm that it was defective my reading solenoid coil continuity. It looked ok so I could not use that info to confirm a bad fill valve, although that possibility was not eliminated. So I ordered a replacement fill valve, removed existing fill valve and took a long position on paper plates. On delivery of the valve, I found that its mounting bracket (which forms a part of the supply pressure boundary) had been redesigned to conform to a year-2000 redesign of the machine. Valve instructions allowed for this and provide for retention of mounting bracket from old valve for use on new valve. Instructions indicated the o ring from new valve (vs old) should be used in attaching the old bracket. I found that the o ring groove in the new valve was so deep that o-ring compression on reassembly was prevented. I went ahead and put together with new o-ring. When turned on supply pressure, it began leaking immediately, so I shut down, removed valve again. During this (2nd) reassembly, I stacked both o rings in same groove in order to get compression at all. Reinstalled valve w/ both o rings....no leaks and it works. I think valve design should be reviewed and depth of o ring groove reduced so only one o ring is needed.

Not really difficult to do. First remove the washer from the counter and flip it over. Carefully determine the correct drawing in the instructions which matches your machine. Follow insructions and double check everything. Took about an hour - and I saved about $350.00 by fixing it myself rather than buying a new one!

Removed the 6 screws and took off the inside pannel. Removed 2 screws that secured the timer.Unplugged old timer leads and put the new one in reverse sequence. Piece of cake.

Identified solinoid responsible for the operation of the drain flapper valve had become damaged, possibly due to its coil shorting and overheating, the inside plastic insulation then melted and came up through the solinoid pin hole. I removed the tension spring holding the flapper drain valve shut, removed the eclip holding the white phenelic arm connected to the tension spring, removed the two screws mounting the solinoid assy. I threw out the bad solinoid. I then proceeded to install the replacement solinoid in reverse order of removal. The end. Works like a champ ! Thank you for your quick shipping response time. My wife is now once again happy. As you know, if my wife isnt happy, I sure wont be happy. :)

Basically, I told my girlfriend, hey, if you are board, this box has the parts to fix the dishwasher in it. When I got home from work, I had to connect one wire, and tighten a couple of screws. The kit has great, easy to follow directions. Thanks!!

pulled out old motor. replaced new motor. works like new.

i couldent use the hole unit because it was for a dryer.

i new the motor would work because it had the same gear and rpm. i couldent find a motor no wear.

Disconnected water, drain, electrical- remove dishwasher.
Place dishwasher on back removed part- replace with new part-reconnected and reinstalled.

I took the inside of the door off of the dishwasher and disconnected the timer, ordered the new timer and with a couple of screws and the attachment of 3 wires I was back in business! Now my dishwasher is working better than ever!