GSD2050F01CC General Electric Dishwasher - Instructions

Plumber had suggested trying a new gasket rather than replace the dishwasher. Ordered one and installed it. Cleaned door and installed gasket in about 30 minutes. So far it works great .... and ... cheaper than new dishwasher.

Our older GE dishwasher was leaking water on the floor while running. After inspecting it while running I was able to determine that the water was coming from the seal around the motors shaft where it entered the pump. I then looked up the washers model number and ordered the impeller shaft seal kit. To my suprise the kit arrived the very next day! After disconnecting the power and water supplies from the dishwasher , I then removed it from the cabinet base and turned it over to gain easy access to the bottom. Using nothing more than a nut driver, adjustable wrench and a pair of pliers I was able to loosen the two compression clamps and two hose clamps that hold the pump to the bottom of the washers tub. I then removed the entire pump and took it to my work bench for the rest of the repair. Removing the plastic impeller strainer was the toughest part.. Lacking the proper spanner wrench, I had no tool that would lock onto the raised tabs to turn it loose with. I was able to position the tabs in the jaws of my workbench vise and giving the entire pump a little twist, It broke free and I was then able to unscrew the rest of the way it by hand.. The old dried up detergent made for a good adhesive, and after removal I cleaned the area completely so the new strainer would thread in easy. I installed the new parts in the kit as per the supplied instructions and re-installed the pump housing back on the dishwasher and put it all back in place. After running it several times not a drip was to be seen, and I was very pleased with the whole process. With the shipping it cost me just $25.00, and it saved me a expensive service call or maybe even the cost of buying a new machine. I would say that overall it was a easy repair but lacking the right tools, you may have some trouble removing the pumps plastic strainer screen as I did. I would highly recommend PartsSelect to anyone, and the entire experience was a good one for me.

The repair was very easy and straight forward. I removed the electrical wires, removed the two hose's and then removed the old valve from the dishwasher frame. To install the new valve, I just did everything in reverse. No problem and I saved about $80 for the repairman to come out and I am sure I would have paid more for the valve if he provided it.

Thank you.

Unscrewed old one and installed the new one.

very easy old part out new part in direct replacement, fit right in and it is working. Great deal and about half of the price than ge website. Thank you.

According to instructions with part

Put on a new cap.

I watched several YouTube videos on how to make the repair. It looked very easy but sometimes professionals, because they've done it before, don't point out small tips that would help a DIY homeowner. The latch goes easily into the inner door slot but there's nothing to hold it there. The videos show the inner and outer door being closed together without showing that you have to hold the latch in place while bringing the outer door up to meet the inner door. Any movement of the inner door makes the latch fall out. So I would say it took me 5 times longer to do this repair than it would if I was doing it again.

Had to pull the dishwasher from under the counter to access the water inlet valve. Disconnected the hoses from the inlet assembly. Removed the inlet assembly from the dishwasher frame. Installed the new assembly and reconnected the hoses. Plugged the dishwasher in, selected a cycle to run to check for leaks.

remove water connection; shut off circuit breaker ; follow the suplied directions; reassemble washer . job done - leak gone. Wife happy.

My husband said it was easy. But the gasket didn't solve the problem. So we had to order another part. We had to order the little black stoppers that go in the hinge area. Still leaked so my husband took them back out and cleaned the area. Then put some kind of sealant in and replaced the black robber things. So far that worked.

Hired my neighbor, who is a plumber.

First of all this site is awesome. So helpful in diagnosing and ordering the part. I highly recommend!

So, the solenoid was melted and needed to be replaced. If you're looking from the front of the dishwasher it's on the left side and it has 2 screws and a c ring. I couldn't get the c ring back on, but the piece stays on without it. Works fine now.

The instructions provided are very good if I had done before. My concern was getting the gasket to sit properly at the bottom where you cannot see. I removed the inside of the door (7 screws) and this made it easier to assure gasket sat properly in the track. may have cost an extra 15 minutes but worth it. If I do again I will take door apart again, however I think this is fixed and should not need attention again.

First I removed the two screws that hold the solinoid in place,then I removed the e clip and unpluged the wire and pulled out the plastic lever with the solinoid and springs. To install Solinoid:First I bolted on the bracket ,then I hooked in the spring in the plastic lever and installed lever on shaft then I hooked in the long spring to the bracket small hole in the bottum then I installed the e clip next I pluged in the wire.Then I tried the Washer .Averthing works fine.