PDW7880J10SS General Electric Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- robert from east windsor, CT
- Parts Used:
- WD18X10010
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Wrench (Adjustable)
old part leaked
unscrewed dishwasher from cabinet, then I flipped dishwasher on it's side. loosen pump motor bracket arm on the end of the motor. loosen pump motor to pump conecter hose clamp and then unscrewed pump motor connector from dishwasher. To install I did the reverse. very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Clay, NY
- Parts Used:
- WD08X10075, WD08X10018
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Leak at bottom of door.
I watched the parts select video and followed their instructions. Only “ issue” was there were no screws on the door behind the exterior skin as in the video, so lifting the inside door liner to put the new lower door seal in was concerning. I was able to pull the liner up enough and slid the seal in with no problem. The video was the key to a smooth repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gaye from LEES SUMMIT, MO
- Parts Used:
- WD08X10075, WD08X10018
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- 30 - 60 mins
The problem is I received the wrong part!
No way to repair since the wrong part was sent. I have sent numerous emails with order numbers, part numbers, model numbers BUT I have no return label to send this back and get a refund. Maybe this will get someone's attention. Pretty disgusted!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from LAS VEGAS, NV
- Parts Used:
- WD15X10014
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Wrench (Adjustable)
Valve leaked
Turn off power and water from dishwasher. Remove Base Access Panel. Remove the upper 2 screws that holds the dishwasher in place. Pull out dishwasher. Locate the valve and remove the 2 screws holding the mounting bracket. (I used a hex Nutdriver to remove the screws) Remove the valve. Disconnect the wire connector. Disconnect water supply. (Place a towel to catch the water) Loosen the hose clamp holding the inlet hose and remove the hose. (I used pliers to loosen the clamp) Remove the elbow from the old valve and reattach to the new valve. (Use teflon tape around the threads) Reverse the Process. Check for leaks. Piece of Cake. Part was an exact fit.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from BATESVILLE, IN
- Parts Used:
- WD12X10163
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The dishwasher detergent dispenser was broken.
The first thing I did was watch the video on the removal of the old broken dispenser and I said to myself that it couldn't be that easy. Well I am going on 70 years old and I was going to call a local to fix it. I bought the new dispenser just to avoid the up-charge. When the conformation email got here with video and written instructions. I watched the video and read the instructions. Just after the part arived (ahead of scheduls) I looked at the machins and said wat the he** what is she going to do to an old man. Got my screwdriver (battery and reversable) and wouldn't you know it . It only took me less then 15 minutes to do the whole job. I can't thank them enough for the video. Wife asked where the part was and almost pased out when I opened the door.. lol Trust these people . They know what they are doing!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- GEORGE from LEVITTOWN, PA
- Parts Used:
- WD15X10014
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
Water leak under Unit
Remove Base Access Panel; Removed Valve Mounting Bracket & Valve; Disconnected Wire Connector; Disconnected Supply Line & distribution Hose; Reversed the Process. Piece of Cake; Part was O.E.M.Component Exact Fit; Took Longer to Write this than it took for Fix. Thanks I Will Be Back for other Parts.!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tom from UPPR CHICHSTR, PA
- Parts Used:
- WD35X21038
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Wheel had melted and support cracked
Removed the lower rack and installed new wheels with clips
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Asok from HELOTES, TX
- Parts Used:
- WD35X21038
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Three of the 8 wheels broke.
The newly purchased wheels have a little different design and could be installed in a matter of few seconds.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nancy from Big Rock, IL
- Parts Used:
- WD35X20994, WD35X20994
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The rack wheels and axles on the DW had broken, causing the upper rack to come flying out when opened.
Took the rack out. Took off the broken wheels and axles. Popped the new ones on, while replacing the rack. Piece of cake! Saved over $100.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carri from Louisville, KY
- Parts Used:
- WD12X10163
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
latch on detergent assembly broken off
Easy repair-removed hex nuts and and screws to pop out old part and replace with new one. New part works better than the original! 1st replacement part arrived with a broken piece, a quick, courteous phone call got a replacement sent out. It took a 2nd phone call to obtain the refund, but the customer care reps are efficient and friendly. I would order from them again for positive service reasons alone.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jerome from Arlington, VA
- Parts Used:
- WD12X10122
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Lost Rinse Aid cap
Inserted new cap purchased from PartSelect.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from Denvr, CO
- Parts Used:
- WD12X10122
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Dispenser Cap Missing
Ordered new cap and put it on when it arrived.
Simple
Simple
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Denise from PALERMO, ME
- Parts Used:
- WD35X21038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Missing wheels
The wheel kit came with axel's to support them. They snapped in place in seconds. No instructions provided, but installing method was obvious.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sharon from THE VILLAGES, FL
- Parts Used:
- WD35X21038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The wheels on the lower rack of our dishwasher kept falling off.
Removed the lower rack. Took off the old wheels. Put the axles on the new wheels which took a little manpower, but became easier once you did a couple (there are 8 wheels). Then snapped the new wheels on the rack which was really simple. The new design is much improved to the old one. The wheels glide better, then they ever did. We're sorry we didn't think of this repair years ago and the cost was a fraction of the cost of a new dishwasher.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DENNIS from MAUMEE, OH
- Parts Used:
- WD12X10163
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Rinse cap was broken
Watched online video, repaired myself in under 10 minutes.
Easy fix with video instructions
Easy fix with video instructions
Was this instruction helpful to you?
Thank you for voting!