EDW2050F01CC General Electric Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- kevin from wellington, FL
- Parts Used:
- WD26X10013
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Wrench set
Dishwasher would not drain
Ordered motor and pump and replaced. Motor pump kit also comes with a drain solinoid so if that was the problem the kit repaired it. One issue is the size of the hanger to ensure the pump does not just hang on its mount. The directions were not very clear and after some trial and error I got it to work to.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward from TUCKAHOE, NY
- Parts Used:
- WD15X10003
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers
Difficult to install the mounting screws
Nut driver and philips screwdriver.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Everett from FREDERICKSBRG, VA
- Parts Used:
- WD15X10003
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers
No water in
Pulled washer out. Found water inlet valve in lower left. Shut off power and water. Replaced valve with new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- clyde from DUNCANNON, PA
- Parts Used:
- WD24X10018
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
water would not pump out of machine
I looked at your web sight and saw how to repair dishwasher.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brian from DERRY, PA
- Parts Used:
- WD15X10003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Wrench (Adjustable), Wrench set
Leaking at the valve
Just like the video and replaced it
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Willard from Los Alamos, NM
- Parts Used:
- WD22X10017
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Part of lower spray arm assembly was broken
This large part is located at the bottom of the tub. It can be accessed by removing the lower dish rack. The assembly is held in place by threads. It can be removed by hand by unscrewing as shown in the PartSelect video. Replacing is just the reverse. The video was very helpful.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brett from Sound Beach, NY
- Parts Used:
- WD26X10013
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Pump/Motor leaking at shaft
This was one of those wonderful repairs where anything went right.
The part arrived overnight as ordered and even though I was abit leary of it fitting, since it was described as a replacement/new design, it fit perfectly! As mentioned in another post here, draining the water out of the unit so I could tip it over to do the replacement was the hardest part!
I'm sure I saved over $100 doing it myself. Thanks PartSelect!
The part arrived overnight as ordered and even though I was abit leary of it fitting, since it was described as a replacement/new design, it fit perfectly! As mentioned in another post here, draining the water out of the unit so I could tip it over to do the replacement was the hardest part!
I'm sure I saved over $100 doing it myself. Thanks PartSelect!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- kevin from longmont, CO
- Parts Used:
- WD26X10013
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
leak between motor and pump housing
repair kit was complete and directions were easy to follow. my model of dishwasher disnt even require any of the adapters. really only required removing a couple of clamps and replacing everything as a single unit
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bonita from Alexandria, VA
- Parts Used:
- WD24X10018
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
End of cycle water in bottom of nDishwasher
Removed screen bottom rear andfound a plunger type part, unscrewed plunger and found it was distressed around it and did not close of a tight seal. Placed new part into location and dishwasher now proforms perfect...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Walter from Yarmouth, ME
- Parts Used:
- WD24X10018
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Frequently get "Blocked Spray Arm" message - washer stops
Removed the 4 screws holding the filter screen assembly in the back of the tub. This exposed the Piston and Nut assembly which unscrewed fairly easily.
Replaced with the new part, put the filter screen assembly back in place ran the machine. The machine still stops with the blocked arm message - just not as frequently. The web researched fix with the piston and nut assembly replacement was obviously not the final answer. I am now out of options I believe except to bite the bullet and get a new machine. Any other suggestions are welcomed.
Replaced with the new part, put the filter screen assembly back in place ran the machine. The machine still stops with the blocked arm message - just not as frequently. The web researched fix with the piston and nut assembly replacement was obviously not the final answer. I am now out of options I believe except to bite the bullet and get a new machine. Any other suggestions are welcomed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Boulder, CO
- Parts Used:
- WD24X10018
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Dishwasher wouldn't drain completely
Remove the back filter to access check valve assembly. Twist check valve assembly to remove, not significant deterioration of rubber cap. Install new assembly. Re-install filter. Super-easy and effective!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JACALYN from TREVOR, WI
- Parts Used:
- WD24X10018
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
dishwasher didn't drain
took out 4 screws pulled piston out and changed put back together. very easy and inexpensive!! thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- charles from baunbridge, GA
- Parts Used:
- WD24X10018
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
water remained in the dishwasher after the running cycle
After two repair people were unable to solve the problem, I read similar stories in your forum and decided to replace the check value as a last ditch effort. Looking at your diagrams it seemed like an easy repair. Removed four screws with nutdriver and replaced value by hand. Ran washer three times and water drained completely. Still puzzled that this wasn't the first thing a repair person would check.
Websight very helpful.
Websight very helpful.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ernest from Johnson City, NY
- Parts Used:
- WD24X10018
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
1-2 inches standing water at end of cycle.
Remove shield in rear. Unscrew valve using hand. Screw new valve in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Chloe from Salisbury, NC
- Parts Used:
- WD24X10018
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
dishwasher was not drainig completly after completing the cycles
Followed the simple instructions to unscrew the old unit and replace with the new one. The unit was easily located on a diagram on the internet and the website instructions for removal were spot on.
Was this instruction helpful to you?
Thank you for voting!