GSD1900G00WH General Electric Dishwasher - Instructions

REmoved the bottom to plates on the dish washer
removed the old solenoid put the new one in and
the washer was fixed. if i could replace it anyone
could do it.

Installed new motor and pump kit. Very easy, except that the instructions did not give any detail on the electrical hook-up. The problem was that the electrical connections for the motor and solenoid were the same on the replacement kit, making it possible to switch them. Be sure and mark the connections from the old unit before removing them.

Basically, I told my girlfriend, hey, if you are board, this box has the parts to fix the dishwasher in it. When I got home from work, I had to connect one wire, and tighten a couple of screws. The kit has great, easy to follow directions. Thanks!!

We bought a used dishwasher that appeared to be in good shape. After installing I ran it through its cycle. It seemed to work fine but after the wash cycle it would not pump out to drain. I found there was a solenoid that controlled the pump direction (drain or to the washer). It tested to see if it was getting power when it was supposed to pump to drain and it was. When I manually actuated the valve the dishwasher pumped out as it was supposed to. With power to the solenoid and the valve working as it should the only peice left was the solenoid. I ordered it from PartsSelect.com and it arrived in 2 days. Installation was only 2 screws and a spring and all now works great.
The on-line parts diagrams and fast shipping make PartsSelect the only choice when buying parts for my appliances.

The repair wouldn't have taken as long as it did if the pictures on the installation sheet were clearer. They were very smudgy. Couldn't see the details on the pictures.

I took the bottom plate off by removing 1 screw on each side. I then pulled the water inlet valve out, disconnected the 2 wires. Because mine was the original inlet valve and GE changed the new one I had to remove the new inlet valve from the face plated and use the old face plate. I then reveresed everything and put it back together and Wah Lah the dishwaher was fixed!!

problem solved..thanks

The finished accent panel on my GE dishwasher was dented and looked awful in my newly remodeled kitchen. I thought about purchasing a new dishwasher but instead searched the web for the part. Found Parts select and it was so easy to compare my part with the graph picture provided. Just count off the boxes for measurement and you will know if you selected the part you need. Access panel arrived in two days,packaged well, and I am happy to have found this website. Give it a try....and returns are easy too if you make a mistake in ordering. My order was perfect on the firt try.

took the moter off and the impellar off replaced the impeller .back and turn the washer back on but it still wouldnt .wash .the moter wouldnt turn .so had the moter tested and it was the moter . found out how and what to look for on you tube .it was a big help in how to fix your washer .typed in model and what kind portable .it was easy .thank you for haveing my part also .and shipping was real fast .

Pulled the dishwasher out from under the counter using a little rug to keep the metal feet from scratching the tile. It is surprisingly light. Old motor and pump are held in mainly by pipe clamps, easy to remove once the washer has been pulled out and turned on its side.

The instructions that came with the pump kit show how to set it up for several different dishwashers. Once you figure out which one you have it is quite easy to set it up. Mine leaked when I first started it up. I pulled it back out and re-tightened the large pipe clamps and it now runs dry.

The dishwasher runs quieter and the dishes come out clean now.

Dishwasher was not filling with water so I assumed the Water Inlet Valve was the problem. I replace the valve but still had the same problem. Studying everything I noticed another problem. The Drain Solenoid which I had replaced 9 months earlier was closed. The plunger was in the down position but must be in up position while washer is filling.
Water was pumped out as soon as it came in. I removed the Drain Solenoid and found the plunger securly stuck inside the plastic cylinder. I forcefully removed it. I knew the solenoid was probably OK because it jerked during the drain cycle. I put emery cloth around a dowel rod and sanded inside the plastic cylinder until plunger moved freely. I smoothed inside with wet or dry sandpaper. After re-installing the solenoid the dishwasher works great. My only explanation is the solenoid has a design flaw and that heat from the solinoid must expand the plastic inward over time.

replaced pump and motor with new one. worked but pump would not empty the water. ordered additional parts check valve,seal and box that check valve screwed into. did not fix problem. Got to looking at replacement pump and discovered thet discharge solonoid was not completely opening the discharge port. I could hold it down manually and the machine would empty. I reported the problem to parts select and they without question shipped me a new pump and motor. took the dishwasher out of the wall again and swapped them out, and now it works fine. the repair was easy and simple. the difficulty was taking the dishwasher out and reinstalling it 3 times. I will use parts select again if the need arises.

Originally replaced solenoid without pulling unit out, but continued to leak. Purchased the entire motor and pump kit; pulled unit out, turned it on end and replaced the motor. The only problem was that no new ground screw was sent with the kit and the existing screw wasn't quite short enough to connect. Either the hole on the replacement kit needs to be deeper or a bond screw needs to be sent that will fit the new kit. We had to find our own screw that would fit properly.

Piece of cake. All done and working just fine.

All new seals