GSD3920C05BB General Electric Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Buddy from Danville, IL
- Parts Used:
- WD26X10013
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers
Pump seal was leaking
I disconnected the power shut off water supply. I then removed the drain hoses and water supply to the old pump. I removed the ground wire and the mounting rod to the old pump. Once removed, I followed the easy illustrated diagrams and instructions that came with the replacement pump.
I mounted the new pump using the supplied hardware and reconnected suply line and drain hose. I turned water supply and power back on. Ran a test cycle before reinserting under countertop. Amazingly quiet and no leaks. Repair a success.
I would use this service again if needed for additonal home appliances.
Thank you
Mr. Buddy King
I mounted the new pump using the supplied hardware and reconnected suply line and drain hose. I turned water supply and power back on. Ran a test cycle before reinserting under countertop. Amazingly quiet and no leaks. Repair a success.
I would use this service again if needed for additonal home appliances.
Thank you
Mr. Buddy King
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roberto from Key Biscayne, FL
- Parts Used:
- WD21X10060
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
Water would not drain out and keep filling up sprayers work
Your video doesn't include disconnecting water supply disconnecting electrical and disconnecting drain hose but after all that the repair to change the solenoid was a easy task but the problem was not solved so I TRIED . thanks Robert
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JACALYN from TREVOR, WI
- Parts Used:
- WD24X10018
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
dishwasher didn't drain
took out 4 screws pulled piston out and changed put back together. very easy and inexpensive!! thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Boulder, CO
- Parts Used:
- WD24X10018
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Dishwasher wouldn't drain completely
Remove the back filter to access check valve assembly. Twist check valve assembly to remove, not significant deterioration of rubber cap. Install new assembly. Re-install filter. Super-easy and effective!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ernest from Johnson City, NY
- Parts Used:
- WD24X10018
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
1-2 inches standing water at end of cycle.
Remove shield in rear. Unscrew valve using hand. Screw new valve in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- stan from philadelphia, PA
- Parts Used:
- WD21X10060
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
water would not drain
Loosened the clamps connecting the pump, disconnected all electric and stabilizer arm. Simply unscrewed the solenoid bracket and replaced with new part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Samuel from LAS VEGAS, NV
- Parts Used:
- WD14X10009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Hinge arm link wore out
Used Phillips screwdriver to undo brackets that keep dishwasher in place. Pulled out dishwasher from underneath the counter. Placed hinge arm in spring, hooked spring onto clip, placed hinge arm in clip. Put back dishwasher under the counter and screwed in place. Took all of 15 minutes. Saved 185.00 for service call.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- charles from baunbridge, GA
- Parts Used:
- WD24X10018
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
water remained in the dishwasher after the running cycle
After two repair people were unable to solve the problem, I read similar stories in your forum and decided to replace the check value as a last ditch effort. Looking at your diagrams it seemed like an easy repair. Removed four screws with nutdriver and replaced value by hand. Ran washer three times and water drained completely. Still puzzled that this wasn't the first thing a repair person would check.
Websight very helpful.
Websight very helpful.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- renee from shelby twp, MI
- Parts Used:
- WD24X10018
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set, Wrench set
standing water at the bottom of the dishwasher
remove the screen at the back bottom of dishwaser. (4 screws). Unthread piston and and nut assembly for check valve....thread in new one.
Problem solved....no more water $10 part....no repair person !!!
Problem solved....no more water $10 part....no repair person !!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Walter from Yarmouth, ME
- Parts Used:
- WD24X10018
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Frequently get "Blocked Spray Arm" message - washer stops
Removed the 4 screws holding the filter screen assembly in the back of the tub. This exposed the Piston and Nut assembly which unscrewed fairly easily.
Replaced with the new part, put the filter screen assembly back in place ran the machine. The machine still stops with the blocked arm message - just not as frequently. The web researched fix with the piston and nut assembly replacement was obviously not the final answer. I am now out of options I believe except to bite the bullet and get a new machine. Any other suggestions are welcomed.
Replaced with the new part, put the filter screen assembly back in place ran the machine. The machine still stops with the blocked arm message - just not as frequently. The web researched fix with the piston and nut assembly replacement was obviously not the final answer. I am now out of options I believe except to bite the bullet and get a new machine. Any other suggestions are welcomed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Martie from FULTON, MO
- Parts Used:
- WD12X10284
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Threads on the cap broken
A no brainer, replaced old fill cap with new fill cap. Delighted I was able to order the part, website is user friendly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stacy from FREEHOLD, NJ
- Parts Used:
- WD22X10008
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
The top of the lower spray arm broke off.
The repair could not have been more easy! We simply unscrewed the broken spray arm and screwed in the new one. For less than $50, we fixed it ourselves. We would have paid in excess of $350 for the repairman to fix it. We could not be more happy with this website, the videos and the fast delivery!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frank from WEST DEPTFORD, NJ
- Parts Used:
- WD08X10057
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Door gasket was old and leaking.
I watched the video instructions and it looked easy! The old gasket just pulled right off easily! Installation of the new gaskets was quick and easy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jamie from MECHANICSBURG, PA
- Parts Used:
- WD28X10013
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Regular and often use, just wear
Literally 1 minute to replace. They are perfect and an easy fix for split tongs on the wine glass holders
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- GREGORY from WARNER ROBINS, GA
- Parts Used:
- WD22X10008
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Top spindle of lower spray arm was broken off
Unscrewed bottom of spray arm support assembly counterclockwise by hand for removal. Inserted new part and screwed it in clockwise by hand for installation. Worked perfectly. Video was helpful.
Was this instruction helpful to you?
Thank you for voting!