GSD3300N10CC General Electric Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- TRAVIS from Webster, MA
- Parts Used:
- WD22X10055
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Socket set
Broken plastic spray arm
There's a video on youtube from this site on how to install spray arm and base. Great video. Great price
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tom from Magnolia, IA
- Parts Used:
- WD18X10039, WD01X10342
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Dishwasher would not drain
Watched a YouTube video description of the repair and ordered parts from this site
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from LAS VEGAS, NV
- Parts Used:
- WD15X10014
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Wrench (Adjustable)
Valve leaked
Turn off power and water from dishwasher. Remove Base Access Panel. Remove the upper 2 screws that holds the dishwasher in place. Pull out dishwasher. Locate the valve and remove the 2 screws holding the mounting bracket. (I used a hex Nutdriver to remove the screws) Remove the valve. Disconnect the wire connector. Disconnect water supply. (Place a towel to catch the water) Loosen the hose clamp holding the inlet hose and remove the hose. (I used pliers to loosen the clamp) Remove the elbow from the old valve and reattach to the new valve. (Use teflon tape around the threads) Reverse the Process. Check for leaks. Piece of Cake. Part was an exact fit.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Merle from Boulder, CO
- Parts Used:
- WD08X10057
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Severe lwater leak around door
Removed door panel. Removed old door seal and cleaned seal recess. Installed new seal. Replaced door panel on door and ran a cycle to check for leaks. Readjusted door latch to correct small leak. Ran another leak test. Job complete and wife is happy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nelson from Oroville, CA
- Parts Used:
- WD28X31819
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Disrack was getting rusty
Removed old rack replaced with new one which was an exact duplicate. Mama's happy; everybody's happy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patricia from Clifton, NJ
- Parts Used:
- WD12X10284
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Dispenser cap would not stay in place because it had melted
First I opened the package and screwed the new dispenser cap into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from Lithia, FL
- Parts Used:
- WD12X10264, WD02X10130
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Rinse Agent Tank Leaks
The following steps were performed: 1) Disconnect power to the dishwasher 2) Unscrew all the screws on the inside of dishwasher door. 3) Remove outside plate on bottom of dishwasher. 4) Separate the dishwasher door after all screws are removed and pull out the old dishwasher rinse agent tank. There is a screw that needs to removed that holds the tank in place as well. 5) Snap in the new rinse agent tank and tighten screw in that holds tank in place. 6) Gently put the inside door back in place. Make sure all the holes line up correctly. 6) Put back the bottom plate of dishwasher. 7) Turn on the power again. You have now completed the repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- GEORGE from LEVITTOWN, PA
- Parts Used:
- WD15X10014
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
Water leak under Unit
Remove Base Access Panel; Removed Valve Mounting Bracket & Valve; Disconnected Wire Connector; Disconnected Supply Line & distribution Hose; Reversed the Process. Piece of Cake; Part was O.E.M.Component Exact Fit; Took Longer to Write this than it took for Fix. Thanks I Will Be Back for other Parts.!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tom from UPPR CHICHSTR, PA
- Parts Used:
- WD35X21038
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Wheel had melted and support cracked
Removed the lower rack and installed new wheels with clips
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lawrence from ROLESVILLE, NC
- Parts Used:
- WD21X10261
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
dishwasher did not start
Took out interlock switch (two leads) and replaced with new one. As simple as that.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Asok from HELOTES, TX
- Parts Used:
- WD35X21038
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Three of the 8 wheels broke.
The newly purchased wheels have a little different design and could be installed in a matter of few seconds.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Helen from Carol Stream, IL
- Parts Used:
- WD12X10284
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Rinse Aid Fill Cap melted because it landed next to the heating element because it wasn't screwed in
Simply screwed in new cap
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Colleyville, TX
- Parts Used:
- WD08X10057
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
Dishwasher leaked
Plumber had suggested trying a new gasket rather than replace the dishwasher. Ordered one and installed it. Cleaned door and installed gasket in about 30 minutes. So far it works great .... and ... cheaper than new dishwasher.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Yuma, AZ
- Parts Used:
- WD28X31819
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
wornout rack
I took out the old one and put the new one in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rhonda from CANTON, GA
- Parts Used:
- WD13X10003
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Latch was broken so dishwasher wouldn't run
I watched several YouTube videos on how to make the repair. It looked very easy but sometimes professionals, because they've done it before, don't point out small tips that would help a DIY homeowner. The latch goes easily into the inner door slot but there's nothing to hold it there. The videos show the inner and outer door being closed together without showing that you have to hold the latch in place while bringing the outer door up to meet the inner door. Any movement of the inner door makes the latch fall out. So I would say it took me 5 times longer to do this repair than it would if I was doing it again.
Was this instruction helpful to you?
Thank you for voting!