GSC3400G00BB General Electric Dishwasher - Instructions

DISCONNECT POWER TO THE DW FIRST! First of all, I need to let you know that my DIY skills usually involve calling someone else to do the job! But I found a couple of good videos online that provided some basic information about the remove/replace steps for the timer. What they DIDN'T warn me about was that there is a spring-loaded lever located directly between the timer and the dw door. When I took the timer off, the lever and spring went flying! The lever that fell off is actually a part of the soap dispenser mechanism. It took me a while (45 minutes) to figure out how all of the pieces went back together. There is a small post on the door that one end of the spring attaches to. The other end of the spring attaches to the open end of the white lever - this lever goes between the timer and the door- kind of an important step to make sure you have these pieces when putting the unit back together! As you put the cover back on the dw door, make sure that the white lever and the black soap dispenser lever are connected (you will have to spin the black lever so that it will connect with the white lever). Just make sure to take your time and breathe! This was a little frustrating at first, but if you relax and try to visualize how the pieces fit together, you'll be running dishes again in no time! Good luck!

I removed the two screw at the top holding the dishwasher to the counter top; pulled on the unit - but found it stuck on something.
Of course the hot water feed and the drain hose were still connected and would not let the unit move out any further as there was no slack.
If I had thought about it - I would have disconnected these from under the adjacent sink. But I ended up lying on the floor trying to disconnect them from underneath the unit. It was a bit difficult as there was very little room to move the wrench and the screwdriver.
Once done, the unit came out very easily.
When tipped over I disconnected the old motor and replaced with the new. It was a very different design but fitted in very easily. The hanger took a bit of working out as the diagrams are not very clear.
The wires and clips went together easily. Once I had cleaned everything around the motor and the gunge that cames from years or washing dishes, it went back the way it came out. Albeit with the same difficulty with feed and drain hose.
We ran the unit with no dishes for a couple of times to clear our the muck left in the pipes when the system was down.
Now we have a fully functioning dishwasher again. Cost $250 for the pump and motor as opposed to the $800+ unit my wife was looking at!

Squeeze the new link to the cable hook with pliers while locking the vise grip to the cable for easier handling. Then, using the vise grip on the cable, hook the other end of the link to the dishwasher door hook

Order the part through you guys and also ask to see if there could be something else wrong. I got an e-mail back the first buisiness day and you sent me the part that day also. I installed the coil and it's be running good ever since. Thanks for your speedy service and technical support.

I took the inside of door off to install both gasket and gasket insert. Much easier this way. Also it’s much easier to fish locking handle through the door if you extend the handle half way and put through opening when raising the door.

I watched the convenient video and saved an old machine that I've grown to love. Plus I didn't have to pay a repair service or have to buy a new machine.
Thanks GE,
T. Dunn

I watched the video instructions and it looked easy! The old gasket just pulled right off easily! Installation of the new gaskets was quick and easy!

I used the pump/motor replacement kit. It was a very easy repair and the parts were a direct replacement with no modification necessary. I saved over $300.

I took the inside door off as shown in the gasket insert video and it made much easier to clean and insert the door gasket.

Took screws out of door panel to get to the latch and replaced old latch with new one. Super easy

from the information previous customers had written.
it saved a lot of fustration and time
and best of all the dish washer does not leak.

Simply opened the dishwasher door, removed the gasket insert located in the middle inside of the door and replaced with new. Also went ahead and replaced the seal on the inner edge of the inside dishwasher door. Found very simple instructions on Google on how to do make this repair. Very easy!

Removed screws and replaced the part. It couldn't of been earlier. Only problem this kit didn't include a toe kick and we are having a hard time finding it.

Removed the 4 screws on front inspection plate and had easy access to solenoid switch. Unplugged unit and switched out with repair kit. So easy a caveman could do it...

I removed 2 screws a wire plug connector and replaced the old part. The total repair including putting the cover plate back on only took about 15 minutes. Also I saved approximately $130.00 by doing this repair my self.