GSD3830Z01WW General Electric Dishwasher - Instructions

Dishwasher had become noisier & noisier in last year during wash & rinse cycles. After looking at various web sites, decided to first pull motor/pump & try cleaning it out. That made no difference. Also looked for anything loose that could cause vibration. No change in operation. Decided to go for replacing motor/pump & found Part Select had best price. Part came next day! I was amazed! Looked at video, then removed old unit and attached new one. Easy because it was exactly same connections. Ran dishwasher and it sounded 100% quieter - like when new! Very happy!!

I unscrewed the lower spray arm and support assembly and then screwed the new part in. Very easy.

Order new part. Lightning fast delivery. Unscrew old one, put in new. 30 seconds. Don't get any easier.

using small flat head screwdriver popped off clips at end of runners --rolled in new rack-- inserted clips back into runners

simply snap new one in place. I will have to say your service was fantastic. I received the new cap 2nd day. I am very pleased and would not hesitate to order something else if needed.

followed the excellent instructions accompanying the gasket.

Dishwasher had flooded. Removed Dishwasher from cabinet and diagnosed problem. Found "PartSelect" on Internet and found Part kit available at reasonable price, in stock to ship immediately. Part #PS260801 [WD26x10013] contained enough parts to make installation easy and also I was able to cure discovery of slit in drain hose that attached to dishwasher drain outlet because kit included a short piece of hose and a hose clamp that allowed hose that had been trimmed to connect to outlet.

Followed easy instructions and completed repair in less than 30 minutes.

Ordered part Monday evening installed it on Wednesday afternoon. Required a pair of pump pliers to loosen old part, new part screwed in by hand. No leaks, no problems. Took longer to explain what caused the problem then it did to fix it. I explained to the owner that overloading the dishwasher was most likely the cause. Dishes can move or fall against the riser during wash, preventing it from dropping back down. Pulling the lower rack out with the riser bound up caused the part to crack. Thanks for the speedy delivery!

In order to replace the upper dishwasher rack I needed to remove the end stoppers on the sliders. They were difficult to remove and one of them broke. I then ordered new end pieces. The new ones had been redesigned and were very easy to insert. If you need to replace the upper rack be certain to order new endpieces along with the order for a new rack. They are quite inexpensive.

Grab the large portion of the assembly and unscrew it- if you've got hard water, this may take some serious effort. Screw in the new part, and your good to go!

I took the dishwasher out from under the sink and looked at the pump and motor, saw that the cooling fan that this old style motor used was broke. Ordered this kit and installed it. I didn't even look at the directions that simple of a swap. Thank God!

My dishwasher used this part # as a substitute for the original part, which i guess is no longer made. After reading the other customers' comments,I thought people were describing two very different experiences with the installation -- some just "popped the cap off the end," or "couldn't be easier." Others had so much difficulty getting the cap off that they broke the cap. I think people must be dealing with totally different kinds of plastic caps. When I started on mine, I couldn't find a way to just "pop" the cap off. It was made so that some small flexible stems or prongs that slid in when installed could not be slid back out. I used a pliers to twist, poke, tilt, bend, whatever I could do to get the plastic cap off the end. That wasn't working, so I tried to bend rims the metal track open, but found the metal was too thick or strong for me to bend it. So I had to twist and force the cap, and the piece that kept the cap on broke off. On one side of the rack it was broken so badly that it couldn't be put back on--kept falling off. Had to try to crimp the rims of the track inward to keep the cap on. It's very loose but it has stayed in for the most part. The cap on the other side cracked enough to get it out without completely breaking off a piece. It went back in better than the first side. Pretty frustrating! I suspect because I don't have the original part with replacement caps to slide in. ?????

The motor/pump Kit I purchased could fix/be installed in any GE dishwasher made since 1970. I would guess that the one I have is about 15-20 years old. I encountered only one small problem with the kit------ a motor hanger that had to be bent a bit to fit correctly. Other than that it was a total breeze. The clear instructions included in the kit helped quite a bit. In 30 minutes or so ,I was done and our machine was back in operation

There is sufficient clearance to remove the motor and pump from under the dishwasher after removal of the front lower panels. This avoids the inconvenience of moving the dishwasher. Some ouch work required to remove some of the fittings as sight lines are obstructed - use a mirror to help. Installation is easier as all but one of the hose and pump clamps can be installed with the screw heads accessible from the front. Only installation issue was that the mounting holes on the pump body for the ground wires and the support piece had been drilled but no screw threads had been cut. Two minutes work with a tap solved the problem. One suggestion is to run a couple of loads before replacing the front cover to check for leaks. I did find one after the second load.