PDWT400V50WW General Electric Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- paul from petaluma, CA
- Parts Used:
- WD15X10014
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Wrench (Adjustable), Wrench set
water dripping near front left of dishwasher
look at neww part first then r&r
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Parry from Vacaville, CA
- Parts Used:
- WD12X10163
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Soap dispenser door wouldn't close
I've never done this before, so I took my time and it took 25 minutes. Now that I know what it looks like inside, it would only take maybe 15 minutes. There are 12 Phillips head screws to remove the front of the washer door. Once off, you need to unplug the large electrical plug to the "dashboard". Remove the screws holding the detergent dispenser, and unplug the two electrical plugs attached. Plug the two plugs back into the new dispenser, and replace the screws, being careful to not tighten to tight. Replace the front of the dishwasher door, with the 12 screws and you're done. Easy job!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anthony from Silver Spring, MD
- Parts Used:
- WD12X10163
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Soap door would not stay closed
Removed the holding screws around the edges; removed and replaced the soap container; reconnected the electrical leads, and done... Very simple fix. But it does get a little tricky since the door is spring loaded. NOTE: THERE ARE SCREWS AT THE BOTTOM THAT IS NOT OBVIOUS.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frances from Goodyear, AZ
- Parts Used:
- WD08X10032
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Our tub gasket was torn by leaning utensils (a definite design flaw.)
Just have a good look at how the original is installed before removing, then clean the area. The new one was a breeze to install, just line it up and pop it in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Peter from Davenport, FL
- Parts Used:
- WD14X10009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Hing arm broke
Removed dish washer from cabinet area and snapped new clip into cable and hook into support.. The time that took the longest was to removed the screws to pull the unit out of the cabinet area.. Very easy fix...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward from Granite Bay, CA
- Parts Used:
- WD08X10032
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
tear in the tub gasket
Pulled out the old gasket and replaced with the new gasket. Inserted the steel spring clip into the ends of the gasket. Repair complete.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Ocala, FL
- Parts Used:
- WD12X10163
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Detergent dispenser would not latch
Repairs do not get any easier than this. Remove 12 screws to disassemble door panel (be careful not to let front panel of assembly to drop or bend when screws release it). Remove 6 screws to remove old detergent dispenser. Unplug cable from old dispenser. Connect cable to new dispenser. Install new dispenser into door with 6 screws and then reassemble door panel with 12 screws making sure to keep all wiring free from pressure points.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dorothea from Dallas, GA
- Parts Used:
- WD12X10163
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Detergent door wouldn't stay closed.
My husband followed the directions included with the replacement part that we ordered. It was so great to read of others' experience installing the part! It works great and we will certainly use this site again. Thank you so much. We saved $100.00 doing it ourselves.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eric from Stephens City, VA
- Parts Used:
- WD12X10122
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Old rinse aid cap melted by heating element
Simply screwed in the new rinse aid cap to replace the old one
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary from Dana Point, CA
- Parts Used:
- WD28X25960
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The rack assembly needed replacing
Just removed the prior rack and put the new one in. Much improved design on the wheels and rack seems of better material as well. The rack does not have as many holders as the prior rack dishes and pans do not fit as well.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Vivian from Belfast, ME
- Parts Used:
- WD12X10163
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Jet Dry Rinse was not dispensing
Removed 8 screws from inside door cover. Opened the door and pulled off two wires from the detergent rinse dispenser with a pair of pliers and removed screws that held the dispenser in place. Removed the dispenser, placed new part in place and put screws back in and put wires back onto the dispenser. Closed cover and screwed back down. Easiest thing I've ever done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Judith from Ventura, CA
- Parts Used:
- WD28X25960
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Rusted and Wheels falling off
I received the part very quickly. I threw away the old rack and put the new one in it's place. No tools or instructions were necessary. The new rack had all of the wheels and combs included. I did not have to purchase them separately. This is a much better designed part than the original rack. The combs are spread differently to better support plates, and the wheels are combined and enclosed to better support the rack. Also, I feel that this was a good price. Thank you!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edith from Petaluma, CA
- Parts Used:
- WD28X25960
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
lower rack was rusting, and one wheel came off
I took the old rack out of the dishwasher, took the new one out of the box it was shipped in and slid it into place. Works great. Need top one soon, but will wait until there's some extra money to order it!!!! Thanks for everything!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cono from Bethlehem, GA
- Parts Used:
- WD02X10169, WD01X10107
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Loud noise when running
Middle arm bearing used a pair of pliers to unscrew the screw and to re-screw with new bearing in place. NO did not have to disconnect the arm. Lower arm turn counter clockwise to remove (comes off very easy) stick needle nose straight down opening and remove bearing. Use needle nose to place new bearing.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- joseph from pittsburgh, PA
- Parts Used:
- WD28X25960
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
bottom rack was rusting away
opened the dishwasher .............removed the old and slid in the new ...then attached by dropping in the utensil compartment.....piece of cake
Was this instruction helpful to you?
Thank you for voting!