PDWT302V00II General Electric Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Marc from Brambleton, VA
- Parts Used:
- WD28X24469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Replace the middle flatware basket
So easy, even I was able to do it. Slide tabs back on defective basket and remove both sides, then slide the tabs onto new basket and place in dishwasher. All Done!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ARTHUR from OAK PARK, IL
- Parts Used:
- WD12X10163
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Pliers, Screw drivers
Detergent dispenser did not work
Followed the instruction video on your website. It was accurate and valid. The repair should have taken 15 mins., instead one of the screws holding the dispenser was frozen. Tried DW-40, and liquid wrench. Neither worked because the screw was in plastic.Finally got out the Dremel and cutting wheels. Had to cut away enough of the unit until I could get at the screw (it was the center bottom one). Sliced through some more of the housing, then cut a notch in the screw head deep enough so I could apply enough pressure with a flat blade screwdriver to open it. After that things went as smoothly as could be expected.A bad design and cheap materials.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from FAIRFIELD, CT
- Parts Used:
- WD28X24469
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Holes in old dishwasher basket
The replacement dishwasher basket easily fit in my dishwasher. Easy to order. Quick delivery. Highly recommended.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Virgil from NAPERVILLE, IL
- Parts Used:
- WD30X10039
- Difficulty Level:
- Difficult
- Total Repair Time:
- More than 2 hours
An old inner rail fell apart and needed replacing
I repaired by replacing both inner rails.
I found that removing an inner rail from the rack is difficult. It can be done with strong fingers separating the tabs of a front Y hook after releasing the rear hook so the rack can slide off the horizontal locator rods. It helps to apply liquid soap to the old inner rails Y clips to reduce friction.
Clean the outer rails thoroughly with a brush and liquid cleaner so the rails can engage
Inserting the inner rails into the outer rails is difficult when they are already attached to the rack. It's much easier to insert the rails independently of the rack. Push the outer rails into the inner rails while applying force to keep them engaged
Attach the rack to the rails by inserting the long rear horizontal rods of the rack into the rear clips of the rail.
Assure the tabs in the rear clips are locked
Again, it helps to apply liquid soap to the new inner rail Y clips to reduce friction
Hold the rails in place and pull the rack forward to engage the front rails with Y clips to the shorter front horizontal rods of the rack.
Force them together to spread the Y clips and lock the rails into them.
I found that removing an inner rail from the rack is difficult. It can be done with strong fingers separating the tabs of a front Y hook after releasing the rear hook so the rack can slide off the horizontal locator rods. It helps to apply liquid soap to the old inner rails Y clips to reduce friction.
Clean the outer rails thoroughly with a brush and liquid cleaner so the rails can engage
Inserting the inner rails into the outer rails is difficult when they are already attached to the rack. It's much easier to insert the rails independently of the rack. Push the outer rails into the inner rails while applying force to keep them engaged
Attach the rack to the rails by inserting the long rear horizontal rods of the rack into the rear clips of the rail.
Assure the tabs in the rear clips are locked
Again, it helps to apply liquid soap to the new inner rail Y clips to reduce friction
Hold the rails in place and pull the rack forward to engage the front rails with Y clips to the shorter front horizontal rods of the rack.
Force them together to spread the Y clips and lock the rails into them.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bob from Chandler, AZ
- Parts Used:
- WD28X25960
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Due the the age of this dishwasher (13 years) both upper and lower racks were showing significant rusting.
This lower rack (GE part #WD28X25960) was ready to roll right into the dishwasher straight out of the box, no tools needed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Samuel from LAS VEGAS, NV
- Parts Used:
- WD14X10009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Hinge arm link wore out
Used Phillips screwdriver to undo brackets that keep dishwasher in place. Pulled out dishwasher from underneath the counter. Placed hinge arm in spring, hooked spring onto clip, placed hinge arm in clip. Put back dishwasher under the counter and screwed in place. Took all of 15 minutes. Saved 185.00 for service call.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- curt from sandy lake, PA
- Parts Used:
- WD12X10163
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The clip that holds the soap dispenser shut broke.
Took screws out that hold front panel on, unplugged wiring, changed soap dispenser, and put everything back together. Not a bad repair at all.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steven from Delanco, NJ
- Parts Used:
- WD12X10163
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
detergent cup latch broke
Very easy - remove the screws around the inside of the door. 6 screws and 2 plugs to remove the assembly. Just be careful not the strip the sheetmetal screws when putting it back together. No screwguns...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joe from WYNNEWOOD, PA
- Parts Used:
- WD28X25960
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Lower rack was bent, didn't like rolling out of the dishwasher anymore
I removed the old rack and saved the flatware container. Then I put the new rack in.
The difference between the old one and the new one is that between a busted grocery cart with one wheel that always wants to return to the parking lot, and a well-trained dog that does exactly what I ask it to. The new rack was worth the $95 I spent to get it.
The new rack came with wheels and axles, so I didn't need to order more.
The difference between the old one and the new one is that between a busted grocery cart with one wheel that always wants to return to the parking lot, and a well-trained dog that does exactly what I ask it to. The new rack was worth the $95 I spent to get it.
The new rack came with wheels and axles, so I didn't need to order more.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Russell from MADISONVILLE, LA
- Parts Used:
- WD15X10014
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set
Had a water leak in bottom of dishwasher.
I simply removed the bad part and reversed the process. It was very easy and a 12 year old could do it. Thanks for the online tips and recommendations. You saved me over 400.00 which is what a new unit would run. Plus installation. Many Thanks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Lancaster, CA
- Parts Used:
- WD28X24469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Missing silverware basket
Popped in the new one and done!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Isabel from Louisville, KY
- Parts Used:
- WD28X25960
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
bottom rack was rusted out
I took out the old rack and rolled in the new. I thought I was going to have to take the rollers off the old one and put them on the new, but they were already on the new rack. The hardest part was getting into the box. I am an 80 year old female.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Myra from Las Vegas, NV
- Parts Used:
- WD28X24469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Silverware Basket broke
I loved the service I received. The site pulled up the correct make and model basket I need for my dishwasher and gave me several options. I order with ease and it arrived within a couple of days. No tools required.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward from Bloomingdale, GA
- Parts Used:
- WD24X10045
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Missing drain hose
Simple as 1,2,3.Parts on time and priced right.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Venice, FL
- Parts Used:
- WD24X10045
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Recived used without drain hose
It was an install. My problem is that the drain tube is not standard to other dishwashers,so I could not get it at either of the local home improvement centers. The good news is that it is larger than the standard, and offers better discharge.
Was this instruction helpful to you?
Thank you for voting!