PDWT280V50SS General Electric Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Calvin from Mankato, MN
- Parts Used:
- WD12X10122
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
aid cap melted
Twisted new one in place of old. Disappointed that there was a melting issue at all. Need to investigate problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- kathy from zionsville, IN
- Parts Used:
- WD28X25960
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Lower Carriage Wheels So Bent It Would Not Move.
Took old one out, put new one in in less than 20 seconds!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- kristen from beaverton, OR
- Parts Used:
- WD28X10128
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Original Silverware basket crumbled under pressure
I took the old one out and replaced it with the new one. It did take both hands as I had to open the dishwasher door while the other hand held the basket. :D
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jerry from Calistoga, CA
- Parts Used:
- WD12X10163
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Dirty Dishes, Dispenser Stopped Working
Ordered part online, arrived two days later. Removed and replaced dispenser with new unit. Easy job. Dishwasher works like new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- joseph from pittsburgh, PA
- Parts Used:
- WD28X25960
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
bottom rack was rusting away
opened the dishwasher .............removed the old and slid in the new ...then attached by dropping in the utensil compartment.....piece of cake
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- MICHELLE from CHESTERFIELD, NJ
- Parts Used:
- WD28X25960
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The Wheel Was Stuck And It Was Hard To Rolled It
I just ordered another one of the wheel rack and it was that easy. No tool required.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Vivian from Belfast, ME
- Parts Used:
- WD12X10163
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Jet Dry Rinse was not dispensing
Removed 8 screws from inside door cover. Opened the door and pulled off two wires from the detergent rinse dispenser with a pair of pliers and removed screws that held the dispenser in place. Removed the dispenser, placed new part in place and put screws back in and put wires back onto the dispenser. Closed cover and screwed back down. Easiest thing I've ever done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary from Dana Point, CA
- Parts Used:
- WD28X25960
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The rack assembly needed replacing
Just removed the prior rack and put the new one in. Much improved design on the wheels and rack seems of better material as well. The rack does not have as many holders as the prior rack dishes and pans do not fit as well.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Chris from Perkasie, PA
- Parts Used:
- WD28X25960, WD28X10128
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Racks wheels fell off
Ordered new and they fit right in. No problems.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Judith from Ventura, CA
- Parts Used:
- WD28X25960
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Rusted and Wheels falling off
I received the part very quickly. I threw away the old rack and put the new one in it's place. No tools or instructions were necessary. The new rack had all of the wheels and combs included. I did not have to purchase them separately. This is a much better designed part than the original rack. The combs are spread differently to better support plates, and the wheels are combined and enclosed to better support the rack. Also, I feel that this was a good price. Thank you!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Harry from Alexandria, VA
- Parts Used:
- WD28X10128
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The base of the basket were broken with use
You sent the correct new part, so repair was remove and replace.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edith from Petaluma, CA
- Parts Used:
- WD28X25960
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
lower rack was rusting, and one wheel came off
I took the old rack out of the dishwasher, took the new one out of the box it was shipped in and slid it into place. Works great. Need top one soon, but will wait until there's some extra money to order it!!!! Thanks for everything!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eric from Stephens City, VA
- Parts Used:
- WD12X10122
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Old rinse aid cap melted by heating element
Simply screwed in the new rinse aid cap to replace the old one
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eddie from Boston, GA
- Parts Used:
- WD28X10128
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
GE Monogram Dishwasher Silverware basket bottom broken on bottom
Replaced identical basket. Service was outstanding from Part Select. Basket was delivered in less than 24 hours from time of order. Truly amazing.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cono from Bethlehem, GA
- Parts Used:
- WD02X10169, WD01X10107
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Loud noise when running
Middle arm bearing used a pair of pliers to unscrew the screw and to re-screw with new bearing in place. NO did not have to disconnect the arm. Lower arm turn counter clockwise to remove (comes off very easy) stick needle nose straight down opening and remove bearing. Use needle nose to place new bearing.
Was this instruction helpful to you?
Thank you for voting!