PDWT280V00SS General Electric Dishwasher - Instructions

Removed screws that held dishwasher under cabinet...pulled out DW...removed old part...replaced with new....easier than falling off a stump.

I handed the parts to my husband and asked him to do it.

After determining that the leak was coming from the sump connector, I had to completely remove the unit from the counter. After removing all the parts in the wash cabinet (wash arms,conduit,fine,course and sump filters),the sump connector nut was revealed which I loosened, but did not remove, with a channel lock plier. The unit was then placed up-side down where I then loosened all the worm clamps that attached the drain motor,pump,and turbidity sensor to the sump and sump connector.then I removed the brackets that braced the pump to the washer body and removed the pump.at this point,you should be able to remove the drain motor and turbidity sensor from the sump and remove the sump from the washer. You should also be able to remove the connector as well.Both these items are made of some type of rubber which seems to deteriorate from the soap which was caked all over them in my case. Just reverse the above process to re-install everthing. I didn't find this job terribly difficult and it was certainly better than spending hundreds replacing the unit.

First broke the tab on trying to get the sprayer arm out - had to buy replacement part. The tab to release the sprayer arm is on the BACK and can't be seen. FYI, pull the tab gently out from the back to release the sprayer arm. Problem wasn't a clogged drain. Next figured it had to be clogged in the Impeller and Seal assembly. Replaced that and realized the motor wouldn't turn. As an electronic engineer, determined the starting capacitor was defective. Found Mr. Nice GET (who owns Hotpoint) would not sell the capacitor, only the entire motor assembly for about $125.00 more or less. Found a capacitor at local motor shop with the correct value and hung it under the dishwasher. (wasn't the right package size to replace where the old one was). All is well - Finally.

took apart lower spray wand cleaned filter noticed sump basket tube to be decaying flaking apart sump filled with white grit and flakes had been using Cascade all it's life and had no problems till new formulation of Cascade and then had all the problems. Steps to replace sump basket #1 turn water and power off to dishwasher #2 disconnect water line, drain line, and power cord #3 remove dishwasher from cabinet #4 open door and remove both upper and lower baskets (upper basket comes off when you remove the end plastic pieces(push in the button like piece from the side of the track and remove the end piece on both sides and the rack comes out)) #5 pull up and off lower spray wand be sure you remove the stainless steel washer that they use as a bearing for the wand #6 remove round white nylon nut(fine filter nut) that holds screen assemble in #7 remove screen by pulling straight up this also has a tube that inserts into the sump #8 remove the main conduit assemble from the pump #9 remove the upper spray wand (center screw)unit should come off #10 remove main conduit from dishwasher #11 remove sump screen cover (you may have to squeeze together to remove #12 remove inner sump basket ( it is held in place by 2 molded catches on either sides of the basket you will have to release these or just pry the side together and lift out) #13 sump cover and basket may break in removal but not expensive parts and will have to be remove before lower dishwasher bottom (perforated screen) can be removed #14 a shop vac to suck out remainder of water from sump may be helpful since now you will have to close door and turn unit upside down #15 lower sump connects to the dishwasher housing by a screw clamp, along with a sensor connection, to the pump intake, and the discharge pump #16 after all clamps are removed and the sensor removed pull the sump off the dishwasher body (note a oval ring inside the sump this mush be retained since it does not come with the new sump #17 assemble in reverse order (NOTE BE SURE TO INSTALL THE OVAL WASHER IN SUMP PRIOR TO PUTTING SUMP BACK ON DISHWASHER BODY and MAKE SURE YOU PUT LOWER DISHWASHER SCREEN (YEA THAT PERFERATED STAINLESS STEEL BOTTOM ON BEFORE YOU PUT THE SUMP SCREEN IN) Also clean and flush the fine screen from any food it may have trapped, the wands flush to make sure your spray ports are clear and not plugged. I replace the sump with a new sump screen and sump cover since they are a little different in the new design from the old. I also dumped Cascade and switched to Finish dishwashing soap it still has some phosphates in it which helps cleaning immensely

Found numerous references on internet that most likely cause was due to a fouled or plugged suction screen. I unscrewed anchor tabs on top securing the dishwasher to the countertop, slightly lowered the front screw legs, turned off circuit breaker at the electrical panel, checked to verify the power was off, removed the small electrical cover under the dishwasher and disconnected the 3 wire nuts, pulled the dishwasher partially out, then disconnected the small corrugated drain hose from the discharge pump under the washer being careful to collect small amount of drain water in a bowl. Finally, carefully pulled dishwasher out from under the countertop leaving the hot water supply hose connected. Tipped washer over onto back (the frame rails are rounded in the back to help facilitate this). Had to unscrew the hose clamps to remove the rubber sump. Then stood the dishwasher back up to disassemble the plastic screen parts from inside the dishwasher. The screen was in fact plugged with white slimy deposits that when dried became chalk like. During cleaning out the white caked on deposits in the rubber sump, I accidentally pushed my screwdriver through a rubber vent stand tube and this is why I had to buy a new rubber sump. The sump rubber material appeared to be partially deteriorated which is why my screwdriver passed through it. Reassembly wasn't very easy. It was difficult to get the rubber sump boot over the plastic flange on the bottom of the tub. It helped to remove the metal hose clamp completely and to have someone hold the dishwasher in place lying on its back while I pushed and prodded to get the rubber seal over the oval flange. Once on, everything went back together easily in reverse order. It probably took me a total of 6 to 8 hours of real working time. But taking into account that I only worked for short periods of time on evenings after work and the fact I had to lug around my extra 70 lbs of gut, the constant laying down and getting back up, the 4 day wait for the new rubber sump to arrive, and my near senior citizen age stretched this 8 hours of work out to a two week home repair project. BUT, I was successful and everything is back to perfect working order. Thank you Partselect.com for having the sump in stock and to my door in only 4 days!

Had purchased SPRING DOOR, CABLE ASM, and HINGE CABLE PULLEY prior to starting repair, as I did not know which piece had failed. Cable assembly was the culprit. SPRING is heavy duty steel, HINGE CABLE PULLEY is nylon, and CABLE ASM (assembly) is braided steel with a steel plate at one end that ties into spring and an inadequate nylon piece that ties into the steel hook on the door. The nylon piece failed through tearing open. REPAIR STEPS: 1. Removed bottom cover plate at front. Two hex head nuts. Nut driver works best but Phillips head screw slots are on nuts. 2. Removed dime-sized cover plates located on either side of main unit where door seals when it is closed. Used Phillips head screwdriver to remove screws that are screwed into cabinets flanking dishwasher. Magnetic tip will help keep you from losing these between dishwasher and cabinet as they are too short to project through the access hole when fully unscrewed. 3. Lowered appliance feet using adjustable pliers. Slip wrench would probably work but six-sided appliance feet are slippery. 4. Loosened drain hose clamp from disposal and removed drain hose. 5. Shut off water line to dishwasher (under sink) and disconnected water line with slip wrench. Steps 4 and 5 were done to give me the slack I needed to pull dishwasher out from cavity far enough to access the side where the repairs were to be made. You may or may not need to do that--try pulling dishwasher out first and see how far it will go. 6. Looked at the problem, which was failed cable assembly. 7. Removed nylon Hinge Cable Pullley with nut driver. This allows cable removal. 8. Put cable back into place (loose) and then replaced Hinge Cable Pulley. 9. Reattached cable to spring on back end and door hook on front end. 10. Pushed dishwasher back into position. 11. Raised appliance feet to proper height. 12. Reinstalled side screws that hold dishwasher against cabinetry. 13. Replaced small screw cover plates. 14. Reattached drain line to disposal. 15. Reattached water line. 16. Turned water on and checked for leaks. 17. Reattached bottom cover plate to front of dishwasher.

This is a somewhat difficult task in that the dishwasher had to be pulled out of the cabinet which required the water inlet hose to be removed (and water to the hose to be shut off). Once the dishwasher was free of the cabinet it had to be flipped over to reach the water inlet valve. Once the valve was replaced go in reverse to reinstall the dishwasher. Worked fine after I got everything installed; no leaks.

removed front panel and replaced new part. Timer did not work because plug kept disconnecting. Called GE service and watched him remove panel without removing control panel. Plug for timer can be installed easily and front panel replaced without disturbing cable.

Replaced wax motor and soap dispenser (all one piece). Only problem was the plastic seal on the very bottom of door had come unseated, and therefore was leaking. You need to check that it is snapped all the way in, and then the leak ceased. Took me a few tries, which made a ten minute repair into an hour long one.

I unscrewed the screws in the door of the dishwasher. Then pulled the inside part of the door up and unscrewed the 6 screws that held the dispenser. I am not sure the correct name of the part but it is on the backside of the dispenser and is red and it is where the wires connect to it, that was probably the most difficult part, disconnecting the plastic covers from the old dispenser. I used a butter knife to pop it out and then was able to get a better grip to pull them off. I pushed the wires on the new red thing and then put the new dispenser in place. You have to make sure that the dispenser is in the right spot and the brace on the underside of the inside part of the door, is in the correct place, otherwise, you will have a leak. Which is what happened to me. I just unscrewed and opened it again and screwed the screws tighter and it was fine.

simply removed broken valve and replaced with new valve, easy peasy. shipping was GREAT, Overnight. all in all a easy fix.

I examined how the old gasket was attached before removing it. I then pushed in the new gasket needing no tools. There has been no water leakage since.

look at neww part first then r&r

The tub gasket is very easy to replace. First I pulled out the old gasket then using the center marking on the new gasket, I centered the gasket at the top then pushed the gasket into the track. At the bottom I reused the wire that holds the two ends in place making sure I attached the separation wire in the same configuration as with the old one. I had another leaking problem with the seal on the bottom of the door. GE does not sell a repair seal for the door bottom and a new inner door must be purchased at around $200. I made that repair using an old bicycle inner tube. I cut the tube into a one inch strip and epoxyed the strip to the tub where the door meets the tub.. Worked perfectly!