Models > PDWT200V00WW > Instructions

PDWT200V00WW General Electric Dishwasher - Instructions

Jump to:

All Instructions for the PDWT200V00WW
106 - 120 of 193
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
ronald from culver city, CA
Parts Used:
WD18X10026
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers
water leak
Came home for lunch to discover the kitchen rug soaked and the dishes I had started when I left that morning unclean. Not sure what happened, pushed start again and immediately found water flowing out from under the machine. pulled the machine out and discovered that mice had chewed through the pliable vinyl sump tank. found the part number in my owners manual and google turned it up on Part Select. this was on Saturday and I had the part Tuesday. very satisfied
Was this instruction helpful to you?
Thank you for voting!
Customer:
Bill from Monterey, CA
Parts Used:
WD15X10014
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
Water leaking on floor
Water was leaking from under refer next to installed under counter dishwasher. Once determined to be dishwasher not refer I removed dishwasher toe place was able to see dripping inlet solenoid valve. I had to disconnect 11V power, shut off inlet water, disconnect inlet water house and remove dishwasher from under counter. Once dishwasher was in center of kitchen I flipped it upside down and removed the electric solenoid inlet valve. Removing the valve took one wrench to remove inlet hose then two wrenches to remove 90 degree brass fitting and another to hold solenoid. I used a nut drive to remove two screws that released the solenoid from the dishwasher frame. I used teflon tape to reattached the 90 degree brass fitting and inlet hose.
Was this instruction helpful to you?
Thank you for voting!
Customer:
michael from north richland hills, TX
Parts Used:
WD12X10163
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
The latch to hold the soap in broke
Replaced the part by taking off the srews on the inside of the dishwasher door (all of them)to get to the backside of the soap dispenser. Remove an electrical connector by pulling (had to pull off using pliers as it was really on there). Then a couple of screws hold to to the inside of the door. Pretty straight forward.
Was this instruction helpful to you?
Thank you for voting!
Customer:
John from GLEN ALLEN, VA
Parts Used:
WD18X10010
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Wrench (Adjustable)
Dishwasher leaking
I had a small leak from under the dishwasher which turned out to be a tiny hole in the Pump Connector. With the power off I pulled the dishwasher out of the cabinet and disconnected the water and drain lines to give me more room. I put the dishwasher on its back to have access to the pump assembly. A couple of nut drivers and the pump connector is accessible. Replaced the pump connector and over tightened it "Crack"... had to replace the Main Conduit connector ($50). I was able to turn a simple $20 repair into a $70 repair. Now that's talent!
Was this instruction helpful to you?
Thank you for voting!
Customer:
Brett from Ocala, FL
Parts Used:
WD18X10010, WD12X10061
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers, Wrench (Adjustable)
Water was leaking out of bottom and not filling washer. Mouse at through this piece
Shut off water, disconnect drain line from disposer. Remove dishwasher from wall and remove water feed line. Unplug or disconnect power to unit. Remove upper and lower dish racks as well as lower water sprayer bar, and filters. Lay dishwasher down on backside (make sure to catch water with bowl). Disconnect pump connector with nut driver and replace. Stand dishwasher back up and reverse removal process
Was this instruction helpful to you?
Thank you for voting!
Customer:
Robert from Evergreen, CO
Parts Used:
WD12X10163
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
Latch on soap dispenser broke
Replacing the soap dispenser was relatively easy, But a word of caution.when I removed the front panel, as it fell off, it pulled the electrical tape out of the door. That of course ruined the electrical panel. Even better, that panel is no longer made. So unless you really want a new dishwasher, be sure you support the front panel when removing. Probably the easiest way to do that (I found out later) is to sit on the floor with the front panel on your legs as youminscrew it. Do read other reviews about how to do the repair as the part comes with no instructions and GE is of virtually no help.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Debra from Caledonia, MI
Parts Used:
WD12X10163
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
wires on the solnoid hard to get off.dd to get off
Used needle nose pliers to get them off.G
Was this instruction helpful to you?
Thank you for voting!
Customer:
Dwight from Phoenix, AZ
Parts Used:
WD12X10163
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers, Screw drivers
Detergent dispenser latch was broken
I was offered a free dishwasher for the taking. The soap dispenser latch was broken. I ordered the part, it arrived two days later by standard delivery. The door cover has to be opened and seperated. The difficulty is that the door will not stay down or up without assistance. Once open, the dispenser is replaced by removing 6 screws from within the door compartment (between the door front cover and inside door wall. Two electrical leads must be removed and reconected to the new part. Removing them is problematic, since one connecter partially chipped off using pliers to gain a grip. After inserting the new part the 6 screws are installed from behind the part and the leads reconnected. There are two ribbon connectors for the control panel and display. They did not come loose so I left them connected, which made it awkward to manipulate the various parts with the door split open. Putting the ribbons in proper place was easy if careful. Securing the outside and inside halves of the door completes the repair. I found instructions on google. This was tricky but easy, as the door parts were often trying to move out of an accessible position for working. Otherwise it was one of the easiest things I have done. It would be easier with two people, and I had only one good arem to work with due to shoulder surgery, but it was successful. The dishwasher works fine, and the price was right at $45.00 in parts plus shipping for a top of the line model.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Roger from Bryant, AR
Parts Used:
WD08X10032
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Leeking gaskets
The tub gasket is very easy to replace. First I pulled out the old gasket then using the center marking on the new gasket, I centered the gasket at the top then pushed the gasket into the track. At the bottom I reused the wire that holds the two ends in place making sure I attached the separation wire in the same configuration as with the old one. I had another leaking problem with the seal on the bottom of the door. GE does not sell a repair seal for the door bottom and a new inner door must be purchased at around $200. I made that repair using an old bicycle inner tube. I cut the tube into a one inch strip and epoxyed the strip to the tub where the door meets the tub.. Worked perfectly!
Was this instruction helpful to you?
Thank you for voting!
Customer:
Robert from Wantage, NJ
Parts Used:
WD15X10014
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
dishwasher was not filling with water
very happy with the product and fast shipping. removed kick plate from dishwasher, inlet valve was on the front left bottom slid out dishwasher removed two screws and disconnected water line,and installed new inlet valve,very simple job if your somewhat handy,make sure you use thred sealant on water line when re installing
Was this instruction helpful to you?
Thank you for voting!
Customer:
Kevin from De Soto, KS
Parts Used:
WD05X10010
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers, Wrench (Adjustable)
Dishwasher would not dry dishes
The quiet power 3 has the heating element in the back, so remove the screws holding the unit in place. Remove the bottom cover and disconnect the water inlet pipe, (after turning off the water of course). Discard the copper tubing if applicable, and pull dishwasher out until you can tilt it forward. Unsrew the plastic nuts and remove the wires for the element. Test the old one to make sure that you need to replace it. When sure of the problem reinstall in the reverse order. Replace the copper with stainless steel braided line and test.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Michael from Ocala, FL
Parts Used:
WD12X10163
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Detergent dispenser would not latch
Repairs do not get any easier than this. Remove 12 screws to disassemble door panel (be careful not to let front panel of assembly to drop or bend when screws release it). Remove 6 screws to remove old detergent dispenser. Unplug cable from old dispenser. Connect cable to new dispenser. Install new dispenser into door with 6 screws and then reassemble door panel with 12 screws making sure to keep all wiring free from pressure points.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Edward from Granite Bay, CA
Parts Used:
WD08X10032
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
tear in the tub gasket
Pulled out the old gasket and replaced with the new gasket. Inserted the steel spring clip into the ends of the gasket. Repair complete.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Gary from Willoughby, OH
Parts Used:
WD26X10056
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers, Socket set
water leak left side of door bottom intermittent
Remove door cover shell by removing screws in inside of door. Unplug harness to control module.Remove outer door shell.Remove four screws at the blower motor. Replace with new motor after disconnecting harness to motor. Reinstall module harness reinstall door shell.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Frances from Goodyear, AZ
Parts Used:
WD08X10032
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Our tub gasket was torn by leaning utensils (a definite design flaw.)
Just have a good look at how the original is installed before removing, then clean the area. The new one was a breeze to install, just line it up and pop it in.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the PDWT200V00WW
106 - 120 of 193