PDWT200V00BB General Electric Dishwasher - Instructions

NOTE I have classified this is a DIFFICULT JOB, but NOT because of the mechanics involved [including the electrical connectors UN-plugging and re-plugging, BUT DUE to the ANALYSIS you need to do to determine whether the SOAP DISH PART or the CONTROLLER is at fault. And this ANALYSIS will probably require you to get into the DISHWASHER DOOR twice. Once to do the analysis and then again to replace whatever part you target. Being you will want to continue to use the DISHWASHER by manually dropping the soap door [or just soap] at the appropriate time in the cycle, while awaiting the new part, which means you have re-button up the door and take it apart again when the new part arrives. . Before starting, view PartSelect's VIDEO on replacing the SOAP DISPENSER, but ignore THE STEPS OF REMOVING AND REPLACING THE SOAP DISPENSER.PART, at this time. The analysis starts with MANUALLY trying to activate the mechanical soap door release on the back of the mounted SOAP DISPENSER, with the soap door closed. It should take only ounces of downward pressure [towards the door hinge] on the vertical plastic piece in a channel near the center of the dispenser, to release the soap door. Next if you have access to an OHM METER {or MULTIMETER} or a DC POWER SUPPLY [to test the the activation of the door release] pull the two connectors on the SOAP DISH SOLENOID [a set pointed pliers will be helpful, as outlined in the VIDEO]. If measuring the SOLENOID's resistance it should read roughly 1800 OHMS. If using a DC POWER SUPPLY, you will probably need at least 25 volts DC to trigger the SOLENOID [NOTE I do not have a variable DC POWER SUPPLY to check it out nor do I know the voltage that the DISHWASHER uses]. Do not bother to measure the resistance of CONTROLLER's driving circuitry [the two wires having connectors], as it will read INFINITY, regardless of whether GOOD or BAD, The CONTROLLER apparently uses a RELAY on this circuit, as opposed to some kind of solid state switch. Replug the SOLENOID connectors. Re-buttoned up the DISHWASHER as shown in the VIDEO, assuming you are going to continue using it If you determine no problems in the above tests, then consider it a CONTROLLER pro0blem and you will need to order one. Otherwise you should have found indications of a SOAP DISPENSER PROBLEM. . When the replacement part arrives and you ready to install it, refer again to PartSelect's VIDEO on replacing the Soap Dish Dispenser for a refresher Following the VIDEO completely, if you replacing the DISPENSER. If you are replacing the CONTROLLER, once inside the DOOR, you will need to remove around 6 individual electrical connectors [before doing ANYTHING REMOVE POWER from the DISHWASHER [as instructed in the VIDEO}. These connectors [all but any single wire connectors] are designed to be plugged only one specific way, so when re-plugging NEVER FORCE a connection, The best way to make sure you do not get confused, take a picture of all the connectors -OR- make notes on the looks and orientation of each multi-wire connector. There is one mounting screw on right side of the CONTROLLER. When installing the new CONTROLLER there are mounting EARS on the left side that are first engaged by having the CONTROLLER tilted up on the right side. Replace the mounting screw. Replugged all the connectors using whatever guide you made. Proceed to put the DOOR back together as outlined in the VIDEO.

Pulled out the old gasket and replaced with the new gasket. Inserted the steel spring clip into the ends of the gasket. Repair complete.

Remove door cover shell by removing screws in inside of door. Unplug harness to control module.Remove outer door shell.Remove four screws at the blower motor. Replace with new motor after disconnecting harness to motor. Reinstall module harness reinstall door shell.

Removed dish washer from cabinet area and snapped new clip into cable and hook into support.. The time that took the longest was to removed the screws to pull the unit out of the cabinet area.. Very easy fix...

The quiet power 3 has the heating element in the back, so remove the screws holding the unit in place. Remove the bottom cover and disconnect the water inlet pipe, (after turning off the water of course). Discard the copper tubing if applicable, and pull dishwasher out until you can tilt it forward. Unsrew the plastic nuts and remove the wires for the element. Test the old one to make sure that you need to replace it. When sure of the problem reinstall in the reverse order. Replace the copper with stainless steel braided line and test.

Replacing the soap dispenser was relatively easy, But a word of caution.when I removed the front panel, as it fell off, it pulled the electrical tape out of the door. That of course ruined the electrical panel. Even better, that panel is no longer made. So unless you really want a new dishwasher, be sure you support the front panel when removing. Probably the easiest way to do that (I found out later) is to sit on the floor with the front panel on your legs as youminscrew it. Do read other reviews about how to do the repair as the part comes with no instructions and GE is of virtually no help.

Used needle nose pliers to get them off.G

I was offered a free dishwasher for the taking. The soap dispenser latch was broken. I ordered the part, it arrived two days later by standard delivery. The door cover has to be opened and seperated. The difficulty is that the door will not stay down or up without assistance. Once open, the dispenser is replaced by removing 6 screws from within the door compartment (between the door front cover and inside door wall. Two electrical leads must be removed and reconected to the new part. Removing them is problematic, since one connecter partially chipped off using pliers to gain a grip. After inserting the new part the 6 screws are installed from behind the part and the leads reconnected. There are two ribbon connectors for the control panel and display. They did not come loose so I left them connected, which made it awkward to manipulate the various parts with the door split open. Putting the ribbons in proper place was easy if careful. Securing the outside and inside halves of the door completes the repair. I found instructions on google. This was tricky but easy, as the door parts were often trying to move out of an accessible position for working. Otherwise it was one of the easiest things I have done. It would be easier with two people, and I had only one good arem to work with due to shoulder surgery, but it was successful. The dishwasher works fine, and the price was right at $45.00 in parts plus shipping for a top of the line model.

The tub gasket is very easy to replace. First I pulled out the old gasket then using the center marking on the new gasket, I centered the gasket at the top then pushed the gasket into the track. At the bottom I reused the wire that holds the two ends in place making sure I attached the separation wire in the same configuration as with the old one. I had another leaking problem with the seal on the bottom of the door. GE does not sell a repair seal for the door bottom and a new inner door must be purchased at around $200. I made that repair using an old bicycle inner tube. I cut the tube into a one inch strip and epoxyed the strip to the tub where the door meets the tub.. Worked perfectly!

Replaced the part by taking off the srews on the inside of the dishwasher door (all of them)to get to the backside of the soap dispenser. Remove an electrical connector by pulling (had to pull off using pliers as it was really on there). Then a couple of screws hold to to the inside of the door. Pretty straight forward.

I had a small leak from under the dishwasher which turned out to be a tiny hole in the Pump Connector. With the power off I pulled the dishwasher out of the cabinet and disconnected the water and drain lines to give me more room. I put the dishwasher on its back to have access to the pump assembly. A couple of nut drivers and the pump connector is accessible. Replaced the pump connector and over tightened it "Crack"... had to replace the Main Conduit connector ($50). I was able to turn a simple $20 repair into a $70 repair. Now that's talent!

Replaced wax motor and soap dispenser (all one piece). Only problem was the plastic seal on the very bottom of door had come unseated, and therefore was leaking. You need to check that it is snapped all the way in, and then the leak ceased. Took me a few tries, which made a ten minute repair into an hour long one.

This is a somewhat difficult task in that the dishwasher had to be pulled out of the cabinet which required the water inlet hose to be removed (and water to the hose to be shut off). Once the dishwasher was free of the cabinet it had to be flipped over to reach the water inlet valve. Once the valve was replaced go in reverse to reinstall the dishwasher. Worked fine after I got everything installed; no leaks.

Opened dishwasher after it completed a wash cycle. Found the rinse dispenser cap had come off during the wash and melted on the heating coil at the bottom of the machine. Pulled cap off of coil, made sure coil was not disturbed. Looked in various sites for cap. Finally found this site where I didn't need to order the whole mechanism and could order just the cap. Received the cap, screwed into the dispenser, fixed. The only problem I had was that there were two possible caps so I picked the one that was the same color as the original one. Project completed. Thanks

First, remove the bottom front covers (two parts four screws). Second, remove the two screws at the top that secure the dishwasher to the counter. Third, gently pull away the dishwasher from underneath the counter just far enough to see and be able to remove the door spring(s) - one on each side. Fourth, remove the existing hinge arm link(s) if not already broken off, replace with the new one(s). Note that the door hinge goes on the door (front) side of the spring and the other side fits into a groove on the door arm - the other end of the spring attaches to one of the 3 available holes on the frame at the bottom. It would be a good idea to replace the hinge arm links on both sides even if only one is broken. Make sure that the door has the right tension (each spring can be hooked in 1 of 3 holes to adjust the tension). Then gently push the dishwasher back under the counter. Finally, replace the screws under the counter and replace the covers on the bottom front. All of this should take no more than 15-20 minutes. This was an easy job!