PDWT100V00BB General Electric Dishwasher - Instructions

This is a somewhat difficult task in that the dishwasher had to be pulled out of the cabinet which required the water inlet hose to be removed (and water to the hose to be shut off). Once the dishwasher was free of the cabinet it had to be flipped over to reach the water inlet valve. Once the valve was replaced go in reverse to reinstall the dishwasher. Worked fine after I got everything installed; no leaks.

After determining that the leak was coming from the sump connector, I had to completely remove the unit from the counter. After removing all the parts in the wash cabinet (wash arms,conduit,fine,course and sump filters),the sump connector nut was revealed which I loosened, but did not remove, with a channel lock plier. The unit was then placed up-side down where I then loosened all the worm clamps that attached the drain motor,pump,and turbidity sensor to the sump and sump connector.then I removed the brackets that braced the pump to the washer body and removed the pump.at this point,you should be able to remove the drain motor and turbidity sensor from the sump and remove the sump from the washer. You should also be able to remove the connector as well.Both these items are made of some type of rubber which seems to deteriorate from the soap which was caked all over them in my case. Just reverse the above process to re-install everthing. I didn't find this job terribly difficult and it was certainly better than spending hundreds replacing the unit.

took apart lower spray wand cleaned filter noticed sump basket tube to be decaying flaking apart sump filled with white grit and flakes had been using Cascade all it's life and had no problems till new formulation of Cascade and then had all the problems. Steps to replace sump basket #1 turn water and power off to dishwasher #2 disconnect water line, drain line, and power cord #3 remove dishwasher from cabinet #4 open door and remove both upper and lower baskets (upper basket comes off when you remove the end plastic pieces(push in the button like piece from the side of the track and remove the end piece on both sides and the rack comes out)) #5 pull up and off lower spray wand be sure you remove the stainless steel washer that they use as a bearing for the wand #6 remove round white nylon nut(fine filter nut) that holds screen assemble in #7 remove screen by pulling straight up this also has a tube that inserts into the sump #8 remove the main conduit assemble from the pump #9 remove the upper spray wand (center screw)unit should come off #10 remove main conduit from dishwasher #11 remove sump screen cover (you may have to squeeze together to remove #12 remove inner sump basket ( it is held in place by 2 molded catches on either sides of the basket you will have to release these or just pry the side together and lift out) #13 sump cover and basket may break in removal but not expensive parts and will have to be remove before lower dishwasher bottom (perforated screen) can be removed #14 a shop vac to suck out remainder of water from sump may be helpful since now you will have to close door and turn unit upside down #15 lower sump connects to the dishwasher housing by a screw clamp, along with a sensor connection, to the pump intake, and the discharge pump #16 after all clamps are removed and the sensor removed pull the sump off the dishwasher body (note a oval ring inside the sump this mush be retained since it does not come with the new sump #17 assemble in reverse order (NOTE BE SURE TO INSTALL THE OVAL WASHER IN SUMP PRIOR TO PUTTING SUMP BACK ON DISHWASHER BODY and MAKE SURE YOU PUT LOWER DISHWASHER SCREEN (YEA THAT PERFERATED STAINLESS STEEL BOTTOM ON BEFORE YOU PUT THE SUMP SCREEN IN) Also clean and flush the fine screen from any food it may have trapped, the wands flush to make sure your spray ports are clear and not plugged. I replace the sump with a new sump screen and sump cover since they are a little different in the new design from the old. I also dumped Cascade and switched to Finish dishwashing soap it still has some phosphates in it which helps cleaning immensely

Replaced wax motor and soap dispenser (all one piece). Only problem was the plastic seal on the very bottom of door had come unseated, and therefore was leaking. You need to check that it is snapped all the way in, and then the leak ceased. Took me a few tries, which made a ten minute repair into an hour long one.

Water was leaking from under refer next to installed under counter dishwasher. Once determined to be dishwasher not refer I removed dishwasher toe place was able to see dripping inlet solenoid valve. I had to disconnect 11V power, shut off inlet water, disconnect inlet water house and remove dishwasher from under counter. Once dishwasher was in center of kitchen I flipped it upside down and removed the electric solenoid inlet valve. Removing the valve took one wrench to remove inlet hose then two wrenches to remove 90 degree brass fitting and another to hold solenoid. I used a nut drive to remove two screws that released the solenoid from the dishwasher frame. I used teflon tape to reattached the 90 degree brass fitting and inlet hose.

Removed the door gasket and cleaned the track prior to installing the new gasket. The online repair instructions didn't mention a thin wire that is stored at the bottom of the tub near the door and is used to hold the ends of the gasket in place. Gently remove the ends of the gasket from the wire prior to pulling the entire gasket out of the machine track.

we followed the instructions as posted on your web site. Once the dishwasher was apart it was self explanatory. We did however need pliers to separate the wires from the old soap dispenser.

Cut power and water flow to the appliance. Laid appliance on its side, removed the electrical lead from the motor. Remove the mount from the back of the motor and loosened the two clamps- one to the sump and one to the discharge tube. Removed and replaced the pump/motor assy. with the new one, reinstalled the clamps, rear mount and electrical lead. Righted the unit and fired it up. Worked fine.

We noticed our detergent door was not opening on cue to dispense the soap and it was leaving our dishes dirty. It came to be that our spring was sprung on the detergent door. I researched it and I could either buy the spring or the whole detergent contraption (installing the contraption was one wrench easier but cost $35 more). Knowing my husband the way I do, I decided to do the more costly route. I followed the instructions from previous installers on here and me and my husband did it in 30 minutes! I do agree that it is a two man job for some of it as I stressed to him NOT to take the front off haphazardly, as it was $400 to replace that! We took the 12 or so screws off, detached the line to the detergent dispenser, reattached, screwed it into the door and replaced the front 12 or so screws again. Easy peasy! Unbelieveable!

I examined how the old gasket was attached before removing it. I then pushed in the new gasket needing no tools. There has been no water leakage since.

Removed dish washer from cabinet area and snapped new clip into cable and hook into support.. The time that took the longest was to removed the screws to pull the unit out of the cabinet area.. Very easy fix...

Open the door and go along entire edge of door and use Philipps to unscrew the front panel of the door from the inside panel of the door. Once unscrewed open carefully. There are screws in the dispenser cup. Undo those and then there are two plugs to be undone. There is also the main black computer component that has to be unplugged from its cord. Just remove and screw everything back the way it was. This was my first time and I am a female age 58 years old. It was simple. If I had to do it again I could do it in less than half the time.

Removing two screws holding the bottom trim/sound baffle opened a view of water dripping from the water intake valve at the left front of my Monogram dishwasher. I then turned off the local (under my adjacent sink) separate feed valve for the washer, then opened the (dedicated) breaker for the machine at my breaker panel.

The replacement valve was identical form and fit to the original. It included the replacement mounting bracket integrated with the valve.

Removing two additional screws holding a bigger sound baffle backed with foam gave good access to replace the valve. The foam was fitted to the power box and a few other obstructions, and apparently stuck to something near the top. I ran my hand up separating the foam from the panel and both then came out easily. I reattached the foam to the panel with clear silicon adhesive.

Removing two screws from the front edge of the bracket holding the valve allowed dropping it down for fairly easy access to the clamp holding the flexible house from the valve to the washer. There wasn’t much slack, so I reached the spring clip with a long plier-like device with cups on the working sold as automotive hose clip tool for that purpose. Regular pliers would likely work, with more skin loss from hands.

That action then allowed pulling the valve out from under the machine (feeding slack in the flexible feed I have installed years ago between that valve and the one under my sink. A small adjustable wrench then made easy work of disconnecting the hose brass coupling from the valve.

The right-angle adapter between the valve body and flexible feed hose is apparently specific to the installation, so it had to be removed and attached to the replacement valve. That was facilitated by placing the valves in a large bench vise, clamping the mounting bracket with the right angle adapter up, and using the adjustable wrench again. The old valve had residue from metal pipe thread sealer, so I used some new sealer on the adapter when installing it. Take care. Getting some inside the valve might be a serious problem. Turn the adapter with the adjustable wrench for a snug fit facing the same direction as the plastic nipple for the machine-side hose.

Installation proceeded easily in reverse of the removal process, using a bit of care to fit that foam back around the intended machine projections. I actually used identical thread lattes screws (wider flange) to hold the upper baffle because I misplaced one of the original screws and decided to originals were distorting the mounting slots because the flanges were too small.

I ran the machine through two cycles before replacing the bottom trim, just to assure there were no leaks. Mild panic when the intake valve didn’t operate as soon as I expected, but it must have been some out of phase control operation, because it eventually operated, then operated as expected during the second cycle.

I unscrewed the screws in the door of the dishwasher. Then pulled the inside part of the door up and unscrewed the 6 screws that held the dispenser. I am not sure the correct name of the part but it is on the backside of the dispenser and is red and it is where the wires connect to it, that was probably the most difficult part, disconnecting the plastic covers from the old dispenser. I used a butter knife to pop it out and then was able to get a better grip to pull them off. I pushed the wires on the new red thing and then put the new dispenser in place. You have to make sure that the dispenser is in the right spot and the brace on the underside of the inside part of the door, is in the correct place, otherwise, you will have a leak. Which is what happened to me. I just unscrewed and opened it again and screwed the screws tighter and it was fine.

I disconnected the pipes to the inlet valve. I removed the bolts from the bracket holding the valve. I tried to use two wrenches to remove the brass angle pipe thingie off the bottom of the old valve. I then beat on it with a hammer, then I just threw it against the basement floor till it came off. I would recommend getting a new brass angle pipe thingie before you start.