PDWF600R30WW General Electric Dishwasher - Instructions

When I first tried to fix the handle I could not figure out where the spring went. I went back online and looked at the diagram of the dishwasher on this site and learned where it went. Once I knew where every piece went it only took me about 5 minutes to put it back in and another 5 minutes to screw the cover back on. I am a newer homeowner and want to be able to do minor fixes. This was my first one and was very happy that I was able to do it on my own.

1. remove old basket. 2 Place new basket.. Done

1. Removed the cap ends from the inner rails - easy

2. Removed the old rusted rack from the inner rails- easy

3. Removed the spray arm and conduit - a bit difficult: there's a hard-to-reach nut that you need to remove at the hub of the spray arm - A pain in the neck because it cannot be reached vertically.

4. Installed the spray arm and conduit onto new rack. Make sure the conduit aligns with the pipe at the rear inner wall! - easy

5. Installed the rack onto the rails - easy

6. inserted the cap ends - done!

No tools required. The seal just pushes into a channel around the tub. The lower ends are held by a wire that spans the lower edge of the door. I started with the lower end since I didn't know just how the seal was installed and found the wire that sticks into the hollow center of the end of the seal. The seal just pulls out so removed it and the wire. Cleaned the seal channel and wire and installed the new seal starting at the bottom and working upwards. after the lower ends are anchored,I found the center of the seal and upper channel and pushed it in place and worked around the corners and down. I did that because I have seen seals stretch as you push them in place and end up in the middle with excess material you have to work back into the seal channel.

Lower assembly only require removal and replacement without tools. Upper assembly required screw driver and pliers to install water wand from old rack to new rack.

The most surprising aspect of this repair was the short 36 hours that it took from order placement to product receipt.

Took out old basket, took off the sprayer arm and put it on the new basket.. pulled out the old wheels on the side tracks and slid the new basket in...pretty simple...

Detached the dishwasher from the cabinet. Slid it out. Removed small guide wheel that the cable went through. Removed the old broken cable. Replaced with new cable. Replaced the guide wheel. Hooked the cable to the door. Hooked the other end to the spring and hooked the spring to the body of the dishwasher. Put some WD40 on the the cable guide. Slide the dishwasher back under the counter and attached it to the cabinets. All done.

Remove screws holding old hose. Attach clamp to new hose with nut driver. Tighten hose and clamp around attachment.

Easy as cake. Perfect part!

Removed the wire clip, then removed two screws on mounting bracket. Then disconected the hose. Removed the brass elbow.

Then reversed these steps and I was done.

The repair itself was simple. I replaced the broken plastic pulley and the cable attached to the door and spring because one end was bent. I also had to remove the fitting that held the pulley in place. In order to access the spring, I had to pull the dishwasher way out and that required disconnecting the water supply, the drain tube, and the electrical wiring! Then I had to reconnect everything. So although the repair took less than 30 minutes, the rest of the work took a couple hours.

I took the front off of the dishwasher door, loosened the screws, unplugged the module and replaced it with the new module. This repair was the easiest repair I've ever completed!

No tools required. The seal just pushes into a channel around the tub. The lower ends are held by a wire that spans the lower edge of the door. The center of the gasket is marked to agree the the tub center.l. The seal just pulls out so I removed it and the wire. Cleaned the seal channel and wire and installed the new seal starting at the Top center and working down to. the lower ends are anchored,I found the center of the seal and upper channel and pushed it in place and worked around the corners and down. It took longer to clean the channel and door than to install the gasket.

The first posted instruction is dead on (except there are 14 phillips screws (not 10) on inside of door. Also, when reconnecting the 2" quick connect, make sure it is fully inserted - otherwise the numbers on the display panel will not show correctly. Mine didn't the first time, and I had to re-open the door panel and giggle around with the connection to get the numbers to display properly.

Turn off water .Remove 4 screws holding lower front panels.Remove panels, valve is on left . Remove 2 screws that hold valve , slip valve up over clip. Using pliers slide clamp back, remove hose from valve.disconnect wire clip , unscrew from water fill line. Install new valve in the reverse order

First of all the part I ordered came a lot sooner than expected.
I thought it would take 5 to 10 days.
I ordered it on a Tuesday and it was at my door on Thursday.
The part was difficult to take off as this was the first time I attempted this.
When the new part came, I saw that I went to too much trouble to take the old one off.
It was installed in about 40 minutes and we were off and running.