GLD7708V00BB General Electric Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Alyce from DIX HILLS, NY
- Parts Used:
- WD35X21041, WD28X10128
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Wheels kept coming off
Wheels and axles come separately and no instructions were included. After a few minutes of looking at the parts, I realized you have to put the axles on the wheels and then snap it on the dish rack. Once I did the first one, the others were easy. Made my dishwasher feel like it was new. Obviously the design of the original wheels was faulty as these were a different design.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barry from FISHKILL, NY
- Parts Used:
- WD35X21041
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
one old roller broke
pulled off all old rollers and axiies and snapped on new ones
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Harinder from CHESTERFIELD, NJ
- Parts Used:
- WD12X10163
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
detergent dispenser was not closing and dishes were dirty
followed the video step by step which was very well expalined and was able to complete the install
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Victor from Phoenix, AZ
- Parts Used:
- WD24X10045, WD01X10279
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Replaced dishwasher but had the wrong drain hose.
Attached the drain hose to the dishwasher pump and to the sink pipes and I was done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lisa from CHARLOTTE, NC
- Parts Used:
- WD35X21041
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The rollers on the bottom rack of my GE Monogram Dishwasher all broke and melted so opening and closing the rack was extremely difficult!
It couldn't have been easier. I installed the new wheels in seconds and the rack glides as perfectly as the day it was installed 11 years ago! Perfection! Your stellar website made it so easy to find the correct parts. BRAVO!!!!! I laughed! I cried! I am so ECSTATIC!!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Melissa from WARNER ROBINS, GA
- Parts Used:
- WD35X21041
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Dishwasher not cleaning properly
The kit came with the anchors and the riollers for the bottom shelf. They clipped right on! Dishwasher cleans great now!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marilyn from CALDWELL, ID
- Parts Used:
- WD35X21041
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Needed to replace rollers on bottom dishwasher rack
Pulled off old rollers and snapped on new ones. Never easier!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- REVERIE from HAMPTON, VA
- Parts Used:
- WD35X21041
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
lower rack wheels kept falling off
delivery of part was very quick, and my husband was able to remove the old part and install the new in about 10 minutes. No service call; no new rack; just a washer that is easy to use again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from JONESBOROUGH, TN
- Parts Used:
- WD15X10014
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Wrench (Adjustable)
Would not fill with water
Ordered most likely part...water inlet valve.
1. Turn off water supply.
2. Remove the metal toe kick plate/insulation at the bottom of the
dishwasher.
3. Remove hose to supply valve.
4. Take electrical plug off old valve.
5. Remove float valve because it was mounted it right in the way of
the 2 screws on the inlet valve bracket.
6. Remove those 2 screws now you can get to them, and move the
inlet valve to one side so you can get to the hose clamp for the
rubber hose out of the valve going to the dishwasher.
7, Take the old valve and bracket out, mount new valve on the
bracket, crawl back down on the floor, reinstall rubber hose and
bracket, and float valve and finally inlet hose.
8. Turn water on. Check hose connections for leaks. Yep, outlet
hose didn't clamp enough now, allowing a drip.
9. Repeat the whole process AGAIN. Replace little clamp
with a REAL hose clamp, reinstall the thing again. No leak this
time.
10. Test run dishwasher thru a cycle. Check again for leaks at hose
connections. OK ? Reinstall insulation pieces and toe kick
plate.
1. Turn off water supply.
2. Remove the metal toe kick plate/insulation at the bottom of the
dishwasher.
3. Remove hose to supply valve.
4. Take electrical plug off old valve.
5. Remove float valve because it was mounted it right in the way of
the 2 screws on the inlet valve bracket.
6. Remove those 2 screws now you can get to them, and move the
inlet valve to one side so you can get to the hose clamp for the
rubber hose out of the valve going to the dishwasher.
7, Take the old valve and bracket out, mount new valve on the
bracket, crawl back down on the floor, reinstall rubber hose and
bracket, and float valve and finally inlet hose.
8. Turn water on. Check hose connections for leaks. Yep, outlet
hose didn't clamp enough now, allowing a drip.
9. Repeat the whole process AGAIN. Replace little clamp
with a REAL hose clamp, reinstall the thing again. No leak this
time.
10. Test run dishwasher thru a cycle. Check again for leaks at hose
connections. OK ? Reinstall insulation pieces and toe kick
plate.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ron from HODGES, AL
- Parts Used:
- WD18X10008
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Small 1/8" hole in side of inlet sump.
Removed the unit from under counter and placed it with the door side down. Removed clamps/bands from the outlets on the sump and removed screws that attached sump to dishwasher tub. Reversed the process with the new sump and positioned the dishwasher unt=der the cabinet. Next step was to remove the arm and cover parts to the sump, then removed the old upper neck portion that stuck to a strainer. Then aligned the strainer to connect to the small neck of the sump and replaced items in the order from which they were removed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DENNIS from MAUMEE, OH
- Parts Used:
- WD12X10163
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Rinse cap was broken
Watched online video, repaired myself in under 10 minutes.
Easy fix with video instructions
Easy fix with video instructions
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rick from Jacksonville, FL
- Parts Used:
- WD08X10018
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Front door on Dishwasher Leaking
Ordered a new tub gasket and, although the gasket went on backorder for two weeks, the repair itself was extremely easy requiring no tools at all!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Diana from NAPLES, FL
- Parts Used:
- WD28X24469
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Old silverware basket wore through and melamine utensils fell through and stuck to heating element which cost me $100 for repairman to remove
Put new basket in, threw old one away
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- steve from parsippany, NJ
- Parts Used:
- WD12X10163, WD12X10146, WD12X10122
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Soap Compartment Door Latch Broken
First removed the eight philips head screws that hold the outside bottom door cover, to get access to the module. Then removed the two wires and the ten screws holding the module in place. Put the new module back in, reconnected the wires, and re-tighten everything. Did not have to use the bracket and cap.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Duncan M. from AYER, MA
- Parts Used:
- WD26X22719
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Wrench (Adjustable), Wrench set
Drain pump failed.
Ordered drain pump kit (GE part # 325). When it came it looked different from the pictures in the manual and what was ordered. Thought I was going to have to retrofit pump. Looked at ordering a drain kit from another source, which I did. When that came it was exactly the same as the one I ordered from Part Select. I returned the other pump.
Looking at the parts diagram, I discovered the replacement pump (part # 325 ordered) was combined with part # 327 which is why it looked different. I went ahead with the replacement, pulling out the pump and the connecting tubing, part # 327. The replacement pump fit exactly in place, replacing the pump and tubing. I put the dishwashing machine back together and it works great.
Bench tested the old pump and it worked. It must have had a food ball caught in the impeller, inhibiting flow. Next time I'll check all the parts for grease and food balls before ordering new parts..
Looking at the parts diagram, I discovered the replacement pump (part # 325 ordered) was combined with part # 327 which is why it looked different. I went ahead with the replacement, pulling out the pump and the connecting tubing, part # 327. The replacement pump fit exactly in place, replacing the pump and tubing. I put the dishwashing machine back together and it works great.
Bench tested the old pump and it worked. It must have had a food ball caught in the impeller, inhibiting flow. Next time I'll check all the parts for grease and food balls before ordering new parts..
Was this instruction helpful to you?
Thank you for voting!