GLD5654V00CS General Electric Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- REVERIE from HAMPTON, VA
- Parts Used:
- WD35X21041
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
lower rack wheels kept falling off
delivery of part was very quick, and my husband was able to remove the old part and install the new in about 10 minutes. No service call; no new rack; just a washer that is easy to use again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DENNIS from MAUMEE, OH
- Parts Used:
- WD12X10163
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Rinse cap was broken
Watched online video, repaired myself in under 10 minutes.
Easy fix with video instructions
Easy fix with video instructions
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ron from HODGES, AL
- Parts Used:
- WD18X10008
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Small 1/8" hole in side of inlet sump.
Removed the unit from under counter and placed it with the door side down. Removed clamps/bands from the outlets on the sump and removed screws that attached sump to dishwasher tub. Reversed the process with the new sump and positioned the dishwasher unt=der the cabinet. Next step was to remove the arm and cover parts to the sump, then removed the old upper neck portion that stuck to a strainer. Then aligned the strainer to connect to the small neck of the sump and replaced items in the order from which they were removed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from JONESBOROUGH, TN
- Parts Used:
- WD15X10014
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Wrench (Adjustable)
Would not fill with water
Ordered most likely part...water inlet valve.
1. Turn off water supply.
2. Remove the metal toe kick plate/insulation at the bottom of the
dishwasher.
3. Remove hose to supply valve.
4. Take electrical plug off old valve.
5. Remove float valve because it was mounted it right in the way of
the 2 screws on the inlet valve bracket.
6. Remove those 2 screws now you can get to them, and move the
inlet valve to one side so you can get to the hose clamp for the
rubber hose out of the valve going to the dishwasher.
7, Take the old valve and bracket out, mount new valve on the
bracket, crawl back down on the floor, reinstall rubber hose and
bracket, and float valve and finally inlet hose.
8. Turn water on. Check hose connections for leaks. Yep, outlet
hose didn't clamp enough now, allowing a drip.
9. Repeat the whole process AGAIN. Replace little clamp
with a REAL hose clamp, reinstall the thing again. No leak this
time.
10. Test run dishwasher thru a cycle. Check again for leaks at hose
connections. OK ? Reinstall insulation pieces and toe kick
plate.
1. Turn off water supply.
2. Remove the metal toe kick plate/insulation at the bottom of the
dishwasher.
3. Remove hose to supply valve.
4. Take electrical plug off old valve.
5. Remove float valve because it was mounted it right in the way of
the 2 screws on the inlet valve bracket.
6. Remove those 2 screws now you can get to them, and move the
inlet valve to one side so you can get to the hose clamp for the
rubber hose out of the valve going to the dishwasher.
7, Take the old valve and bracket out, mount new valve on the
bracket, crawl back down on the floor, reinstall rubber hose and
bracket, and float valve and finally inlet hose.
8. Turn water on. Check hose connections for leaks. Yep, outlet
hose didn't clamp enough now, allowing a drip.
9. Repeat the whole process AGAIN. Replace little clamp
with a REAL hose clamp, reinstall the thing again. No leak this
time.
10. Test run dishwasher thru a cycle. Check again for leaks at hose
connections. OK ? Reinstall insulation pieces and toe kick
plate.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeremy from TAOS, NM
- Parts Used:
- WD21X10505
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Everything dead
1. Troubleshoot: Unplug, check power at outlet (OK), disassemble front door (phillips screws) from inside, remove safety switch cover to check operation (OK), remove metal shield over ckt board. Noticed burned and separated transformer leads. No repair possible, ordered new board(s), arrived promptly. 2. Replace: Piece of cake--remember to check for jumpers, had to remove one from old board and put it on the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- charles from royal oak, MI
- Parts Used:
- WD12X10401
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
a couple of retaining ears were broken from the cover allowing the the switches and plunger to move out of place
took screws from inside door panel and replaced the cover taking care not to allow plunger and spring to pop out put panel in place and screwed down
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rick from Jacksonville, FL
- Parts Used:
- WD08X10018
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Front door on Dishwasher Leaking
Ordered a new tub gasket and, although the gasket went on backorder for two weeks, the repair itself was extremely easy requiring no tools at all!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michelle from Spokane Valley, WA
- Parts Used:
- WD35X21041, WD35X21041
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The plastic wheels kept falling off the bottom rack of the dishwasher
The old wheels and attachment brackets were easily removed since they were always falling off. I ordered all new brackets and wheels, but it turns out I didn't need new wheels. If your original wheels are in good condition, they are the same size as the new ones and fit the new brackets. The new attachment brackets are built differently than the ones that came with the dishwasher, but (a good thing considering the originals only lasted 1 1/2 years). The new brackets and wheels snapped together and snapped into place on the dishwasher in minutes--no tools were needed. It took longer to cut the parts out of the packaging than to install them. The bottom rack now rolls out like it did when it was brand new. Definitely worth the few dollars in parts.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Amelia from PEORIA, IL
- Parts Used:
- WD28X25960
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Rack was rusted and broken.
It was a very simple replacement. I took the old one out and rolled the new one in. It took less than 5 minutes!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from North Charleston, SC
- Parts Used:
- WD08X10018
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Leaking from front
I removed the old gasket very easily as there wasn't even glue holding it in place. The new gasket just pressed right into a slot and makes a water tight seal.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Chris from Medina, MN
- Parts Used:
- WD35X21041, WD35X21041
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Original wheels kept falling off, rack would go off track and it drove me crazy
Simple, took five minutes, no tools, problem solved.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wayne from SEASIDE, OR
- Parts Used:
- WD35X21041
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Older wheels had broken clips.
Simply remove broken wheels and clip on replacements. No tools are necessary for this fix and the replacement was inexpensive and easy to install. The kit worked beautifully.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from BURKBURNETT, TX
- Parts Used:
- WD12X10206
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Rinse aid cap leaking
Opened the door on dishwasher and installed the rinse aid cap. Checked for leaks. None found
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Suzanne from CHEYENNE, WY
- Parts Used:
- WD12X10109, WD12X10061
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Old parts showing wear
Watched a YouTube video on disassembly, parts replacement, and reassembly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jonni from VACAVILLE, CA
- Parts Used:
- WD28X25960
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
leg fell off of bottom rack.
Slid it in. Very easy and the replacement part is built better than the original part.
Was this instruction helpful to you?
Thank you for voting!