GLD4500V00BB General Electric Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Tom from UPPR CHICHSTR, PA
- Parts Used:
- WD35X21038
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Wheel had melted and support cracked
Removed the lower rack and installed new wheels with clips
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Asok from HELOTES, TX
- Parts Used:
- WD35X21038
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Three of the 8 wheels broke.
The newly purchased wheels have a little different design and could be installed in a matter of few seconds.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- arthur from ALMENA, WI
- Parts Used:
- WD24X10045
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
drain pipe was missing when purchased used dishwasher
oversized outlet not available in local stores, this one fit perfectly
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nathaniel from HAWKINSVILLE, GA
- Parts Used:
- WH23X10028
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Would NOT drain
Flipped washer on side
Did repair from bottom
Really easy repair
Did repair from bottom
Really easy repair
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from TEMPLE, TX
- Parts Used:
- WD28X10384
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Old lower dish rack had rusted in places due to some of the protective coating wearing off.
It is extremely easy. Just take out the old lower rack and slide in the new rack. Remove the silverware holder from the old rack and insert it into the new rack.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from JONESBOROUGH, TN
- Parts Used:
- WD15X10014
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Wrench (Adjustable)
Would not fill with water
Ordered most likely part...water inlet valve.
1. Turn off water supply.
2. Remove the metal toe kick plate/insulation at the bottom of the
dishwasher.
3. Remove hose to supply valve.
4. Take electrical plug off old valve.
5. Remove float valve because it was mounted it right in the way of
the 2 screws on the inlet valve bracket.
6. Remove those 2 screws now you can get to them, and move the
inlet valve to one side so you can get to the hose clamp for the
rubber hose out of the valve going to the dishwasher.
7, Take the old valve and bracket out, mount new valve on the
bracket, crawl back down on the floor, reinstall rubber hose and
bracket, and float valve and finally inlet hose.
8. Turn water on. Check hose connections for leaks. Yep, outlet
hose didn't clamp enough now, allowing a drip.
9. Repeat the whole process AGAIN. Replace little clamp
with a REAL hose clamp, reinstall the thing again. No leak this
time.
10. Test run dishwasher thru a cycle. Check again for leaks at hose
connections. OK ? Reinstall insulation pieces and toe kick
plate.
1. Turn off water supply.
2. Remove the metal toe kick plate/insulation at the bottom of the
dishwasher.
3. Remove hose to supply valve.
4. Take electrical plug off old valve.
5. Remove float valve because it was mounted it right in the way of
the 2 screws on the inlet valve bracket.
6. Remove those 2 screws now you can get to them, and move the
inlet valve to one side so you can get to the hose clamp for the
rubber hose out of the valve going to the dishwasher.
7, Take the old valve and bracket out, mount new valve on the
bracket, crawl back down on the floor, reinstall rubber hose and
bracket, and float valve and finally inlet hose.
8. Turn water on. Check hose connections for leaks. Yep, outlet
hose didn't clamp enough now, allowing a drip.
9. Repeat the whole process AGAIN. Replace little clamp
with a REAL hose clamp, reinstall the thing again. No leak this
time.
10. Test run dishwasher thru a cycle. Check again for leaks at hose
connections. OK ? Reinstall insulation pieces and toe kick
plate.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DENNIS from MAUMEE, OH
- Parts Used:
- WD12X10163
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Rinse cap was broken
Watched online video, repaired myself in under 10 minutes.
Easy fix with video instructions
Easy fix with video instructions
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jimmy G from SPRING, TX
- Parts Used:
- WD15X10014
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
Water leakage at valve
I watched the video that came with email on part. Gave instructions on how to. Thank you !
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ron from HODGES, AL
- Parts Used:
- WD18X10008
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Small 1/8" hole in side of inlet sump.
Removed the unit from under counter and placed it with the door side down. Removed clamps/bands from the outlets on the sump and removed screws that attached sump to dishwasher tub. Reversed the process with the new sump and positioned the dishwasher unt=der the cabinet. Next step was to remove the arm and cover parts to the sump, then removed the old upper neck portion that stuck to a strainer. Then aligned the strainer to connect to the small neck of the sump and replaced items in the order from which they were removed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Cincinnati, OH
- Parts Used:
- WD35X21038, WD12X10206
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Rack roller and JetDry cap were missing
Opened the package, opened the plastic parts bag, installed the roller and the cap.
Whew!
Whew!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rick from Jacksonville, FL
- Parts Used:
- WD08X10018
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Front door on Dishwasher Leaking
Ordered a new tub gasket and, although the gasket went on backorder for two weeks, the repair itself was extremely easy requiring no tools at all!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- charles from royal oak, MI
- Parts Used:
- WD12X10401
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
a couple of retaining ears were broken from the cover allowing the the switches and plunger to move out of place
took screws from inside door panel and replaced the cover taking care not to allow plunger and spring to pop out put panel in place and screwed down
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeremy from TAOS, NM
- Parts Used:
- WD21X10505
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Everything dead
1. Troubleshoot: Unplug, check power at outlet (OK), disassemble front door (phillips screws) from inside, remove safety switch cover to check operation (OK), remove metal shield over ckt board. Noticed burned and separated transformer leads. No repair possible, ordered new board(s), arrived promptly. 2. Replace: Piece of cake--remember to check for jumpers, had to remove one from old board and put it on the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Denise from PALERMO, ME
- Parts Used:
- WD35X21038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Missing wheels
The wheel kit came with axel's to support them. They snapped in place in seconds. No instructions provided, but installing method was obvious.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- tim from prior lake, MN
- Parts Used:
- WD12X10163
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The soap dispenser would not close.
This was simple. I took the door apart with a portable screw driver. Then I detached the wires and unscrewed the old module and replaced it. I then put the door back together, loaded the dishwasher and it cleaned my dishes. Even for this `old dog' it was easy.
Was this instruction helpful to you?
Thank you for voting!