GHDT168V50SS General Electric Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Andrew from DeWitt, MI
- Parts Used:
- WD35X21041
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken axle on one wheel
Only one axle was broken, but I replaced all 8 because GE had redesigned the axle to prevent future problems. Decided to just replace them all and be done with it. Took 10 minutes, start to finish and all is well.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Denver, CO
- Parts Used:
- WD35X21041
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
wheel studs were worn out, glide arm stopper part gone, needed wheels for upper level tray
Very easy, saw the parts I needed online, ordered them, and installed them. Easier than I thought. Saved probably $200 in having a repair man come to the house. Outstanding results! Thank you!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marc from Sebastopol, CA
- Parts Used:
- WD35X21041
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Axle attachment breaks on lower rack
Remove all wheels on one side. Use pliers to remove broken axles from wheels. Pop in new axles, then go to lower rack and attach to rack by pushing axle pinch mechanism onto rack support. New axles do not look like old ones—they are improved.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from West Point, IA
- Parts Used:
- WD35X21041
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
three lower tray wheels broken
Used plier to pinch the axle head to take the old wheels off then pushed the new wheels on by hand.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jonathan from New York, NY
- Parts Used:
- WD35X21041
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Wheels keep falling off dish rack.
So easy and the posts on the site were incredibly helpful in determing what part i needed. The wheels on the dish rack inside the dishwasher kept falling off. I had to keep lifting the dish rack in and out of the dish washer to load and unload it. Unbelievably annoying. I popped the old wheel axels out of the exisiting wheels and replaced them with the new wheel axels I ordered from PartSelect. Then I attached the wheels back on the dish rack and it was right back to normal.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Suzanne from Oak Ridge, NJ
- Parts Used:
- WD35X21041
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
The wheels kept falling off the bottom rack of the dishwasher
My husband took off all the wheels and changed the axles. We had friends who had the same problem and they led us to your web site.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Vicki from Mooresville, NC
- Parts Used:
- WD12X10163
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Soap Dispenser latch broke
I removed six screws and unplugged the module and removed.
Replaced by the new module and plugged in and then replaced the six screws.
Very easy to fix.
Replaced by the new module and plugged in and then replaced the six screws.
Very easy to fix.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sharon from Northfield, MN
- Parts Used:
- WD35X21041, WD35X21041, WD08X10032
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
difficulty rolling the lower rack in and out of dishwasher
Replaced all 8 of the wheels and axles (the old axles wouldn't hold the wheels in place any longer). Replaced the tub gasket because of cuts from knives. Both fixes were relatively easy to do, although directions for the tub gasket would have been nice!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donna from Arlington, TN
- Parts Used:
- WD15X10014
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Water leaking out from bottom of Dishwaser
Very easy! Removed 4 screws that was holding the valve to the bracket. Placed bracket over water inlet line. Attached copper threaded coupling with pliers.Screwed valved on to the coupling. Attached bracket to the valve with 4 screws. Reattached water line. Attached bracket to frame of dishwaser. Put kickplate back on and done!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rebecca from West Friendship, MD
- Parts Used:
- WD35X21041
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The wheels fell off the bottom rack of the dishwasher
The replacement studs that were suggested fixed the problem that we were having. The fix was easy and took less than ten minutes to take the broken studs out and snap the new ones into place. The studs are designed to hold onto the rack much tighter than the original studs and completely fixed the problem of the wheels falling off anytime you tried to move the bottom rack.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lucille from North Babylon, NY
- Parts Used:
- WD35X21041
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
bottom rack had bad design on wheels and kept falling off making the dishwasher unuseable
I ordered wheels on this wonderful site that looked like they made more sense and replaced all eight on my dishwasher and FINALLY the dishwasher isn't the nightmare it has been. It took seconds to pop in the clip to the roller and pop it on the rack. Thank you PartsSelect
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John F from Ridgewood, NJ
- Parts Used:
- WD35X21041
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Wheels fell off lower rack
Contacted PartsSelect online on Thursday. Saturday the parts arrived. My son and I pulled the old connectors off the wheels and snapped the new ones in place. Then he snapped all the wheels onto the rack. DONE. I still find myself wanting to lift the rack now but the wheels are on and I am happy. All around EXCELLENT. Thank you.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Melissa from Vienna, VA
- Parts Used:
- WD35X21041
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
New wheels for lower rack on dishwasher.
Ordered on a Friday and parts arrived Sat. No tools required. Pieces easily slipped into place. Dishwasher is all fixed. This site is much easier to use than GE's. Will use PartSelect for all future replacement parts.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jason from Omaha, NE
- Parts Used:
- WD35X21041
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Needed new wheels
I inserted wheel axle into wheel and attached to bottom rack axle. It was simple. No problems.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Glen from Garland, TX
- Parts Used:
- WD35X21041
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
Wheels kept coming off dishwasher basket upon pull out
I hand removed the snap in wheel axels and replaced the axles with new ones, by hand, no tools needed. On this dishwasher basket the wheeel axels just snap onto the metal cage "wires" of the roll out basket holding the dishes. Very simple. Used pliers to squeeze each old axle retaining nubs,from each of the eight wheels, , then just slipped (pulled the wheels off the axles) and discared only axles (that here the problem, detaching frequently from grasping the pull out dish basket, due to heat taking the temper out of their gripper (to basket).
Was this instruction helpful to you?
Thank you for voting!