GDWT708V55BB General Electric Dishwasher - Instructions

opened the dishwasher .............removed the old and slid in the new ...then attached by dropping in the utensil compartment.....piece of cake

I just ordered another one of the wheel rack and it was that easy. No tool required.

Ordered part online, arrived two days later. Removed and replaced dispenser with new unit. Easy job. Dishwasher works like new.

I took the old one out and replaced it with the new one. It did take both hands as I had to open the dishwasher door while the other hand held the basket. :D

Took old one out, put new one in in less than 20 seconds!

Simply took out the broken rack and inserted the new one.

Twisted new one in place of old. Disappointed that there was a melting issue at all. Need to investigate problem.

Just pulled out the old basket and put in the new one. . Don't know the holes got into the basket. . .

Installed new rack assembly and it works fine. Thanks

Opened dishwasher after it completed a wash cycle. Found the rinse dispenser cap had come off during the wash and melted on the heating coil at the bottom of the machine. Pulled cap off of coil, made sure coil was not disturbed. Looked in various sites for cap. Finally found this site where I didn't need to order the whole mechanism and could order just the cap. Received the cap, screwed into the dispenser, fixed. The only problem I had was that there were two possible caps so I picked the one that was the same color as the original one. Project completed. Thanks

removed original rack, inserted replacement.

Remove door cover shell by removing screws in inside of door. Unplug harness to control module.Remove outer door shell.Remove four screws at the blower motor. Replace with new motor after disconnecting harness to motor. Reinstall module harness reinstall door shell.

we followed the instructions as posted on your web site. Once the dishwasher was apart it was self explanatory. We did however need pliers to separate the wires from the old soap dispenser.

NOTE I have classified this is a DIFFICULT JOB, but NOT because of the mechanics involved [including the electrical connectors UN-plugging and re-plugging, BUT DUE to the ANALYSIS you need to do to determine whether the SOAP DISH PART or the CONTROLLER is at fault. And this ANALYSIS will probably require you to get into the DISHWASHER DOOR twice. Once to do the analysis and then again to replace whatever part you target. Being you will want to continue to use the DISHWASHER by manually dropping the soap door [or just soap] at the appropriate time in the cycle, while awaiting the new part, which means you have re-button up the door and take it apart again when the new part arrives. . Before starting, view PartSelect's VIDEO on replacing the SOAP DISPENSER, but ignore THE STEPS OF REMOVING AND REPLACING THE SOAP DISPENSER.PART, at this time. The analysis starts with MANUALLY trying to activate the mechanical soap door release on the back of the mounted SOAP DISPENSER, with the soap door closed. It should take only ounces of downward pressure [towards the door hinge] on the vertical plastic piece in a channel near the center of the dispenser, to release the soap door. Next if you have access to an OHM METER {or MULTIMETER} or a DC POWER SUPPLY [to test the the activation of the door release] pull the two connectors on the SOAP DISH SOLENOID [a set pointed pliers will be helpful, as outlined in the VIDEO]. If measuring the SOLENOID's resistance it should read roughly 1800 OHMS. If using a DC POWER SUPPLY, you will probably need at least 25 volts DC to trigger the SOLENOID [NOTE I do not have a variable DC POWER SUPPLY to check it out nor do I know the voltage that the DISHWASHER uses]. Do not bother to measure the resistance of CONTROLLER's driving circuitry [the two wires having connectors], as it will read INFINITY, regardless of whether GOOD or BAD, The CONTROLLER apparently uses a RELAY on this circuit, as opposed to some kind of solid state switch. Replug the SOLENOID connectors. Re-buttoned up the DISHWASHER as shown in the VIDEO, assuming you are going to continue using it If you determine no problems in the above tests, then consider it a CONTROLLER pro0blem and you will need to order one. Otherwise you should have found indications of a SOAP DISPENSER PROBLEM. . When the replacement part arrives and you ready to install it, refer again to PartSelect's VIDEO on replacing the Soap Dish Dispenser for a refresher Following the VIDEO completely, if you replacing the DISPENSER. If you are replacing the CONTROLLER, once inside the DOOR, you will need to remove around 6 individual electrical connectors [before doing ANYTHING REMOVE POWER from the DISHWASHER [as instructed in the VIDEO}. These connectors [all but any single wire connectors] are designed to be plugged only one specific way, so when re-plugging NEVER FORCE a connection, The best way to make sure you do not get confused, take a picture of all the connectors -OR- make notes on the looks and orientation of each multi-wire connector. There is one mounting screw on right side of the CONTROLLER. When installing the new CONTROLLER there are mounting EARS on the left side that are first engaged by having the CONTROLLER tilted up on the right side. Replace the mounting screw. Replugged all the connectors using whatever guide you made. Proceed to put the DOOR back together as outlined in the VIDEO.

I began to notice a loud grinding sound when my dishwasher blower motor kicked in (mostly at the end of the entire washing cycle). It was obvious where the noise was coming from (upper left side of door). Ordered blower motor / fan and replaced it. Problem solved! When taking the front panel off, be very aware of all screws. There is a screw on the right side of the door that screws inward. It holds the control unit. If not removed, the control unit screw hole will break off and it will be difficult for you to secure the control unit. Be aware that there are two small screws that point UP below the front panel. Be sure to remove those too. Take pictures of the wires before disconnecting from the control unit. It's fairly obvious, but cheap insurance if needed when reassembling. The fan motor in the upper left of the panel. There are a large gray venting unit above it. You will need to remove that unit in order to expose the screws to remove the fan motor. Once removed, replace the fan motor and work backwards to connect everything again. Possibly take a few moments to clean the inside of your door panel to remove any hard water build up from any moisture that leaked into your door panel. Hope this helps.