GDWT668V50SS General Electric Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- DENNIS from MAUMEE, OH
- Parts Used:
- WD12X10163
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Rinse cap was broken
Watched online video, repaired myself in under 10 minutes.
Easy fix with video instructions
Easy fix with video instructions
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lisa from CHARLOTTE, NC
- Parts Used:
- WD35X21041
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The rollers on the bottom rack of my GE Monogram Dishwasher all broke and melted so opening and closing the rack was extremely difficult!
It couldn't have been easier. I installed the new wheels in seconds and the rack glides as perfectly as the day it was installed 11 years ago! Perfection! Your stellar website made it so easy to find the correct parts. BRAVO!!!!! I laughed! I cried! I am so ECSTATIC!!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marilyn from CALDWELL, ID
- Parts Used:
- WD35X21041
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Needed to replace rollers on bottom dishwasher rack
Pulled off old rollers and snapped on new ones. Never easier!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- REVERIE from HAMPTON, VA
- Parts Used:
- WD35X21041
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
lower rack wheels kept falling off
delivery of part was very quick, and my husband was able to remove the old part and install the new in about 10 minutes. No service call; no new rack; just a washer that is easy to use again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Melissa from WARNER ROBINS, GA
- Parts Used:
- WD35X21041
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Dishwasher not cleaning properly
The kit came with the anchors and the riollers for the bottom shelf. They clipped right on! Dishwasher cleans great now!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anthony from East Islip, NY
- Parts Used:
- WD18X10026, WD18X10010
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Socket set, Wrench set
Water leaking underneath dishwasher
went online to parts select. Looked at parts that could be leaking. Thought it was the sump. Purchased the sump and the pump connector. Almost bought the adaptor pump assembly, but it was $29.00. Parts arrived in about 2 days. Turned off water and power to dishwasher. Disconnected the copper water line. Hardest part was getting the dishwasher out of space. Once out, layed it on it's side. Parts held together with clamps. Took it apart like a puzzle. Replaced the parts, tightened the clamps. Pump connector hard to unscrew. Got a good hand grip on it and turned it loose. Sump did have a hole in it. Put everything back together. water, electric, etc. Turned it on and it was leaking. Leak coming from the adaptor pump assembly. Couldn't wait 2 more days.Found part at a local parts store for $40.00. Was able to change it by reaching underneath and not pulling dishwasher out again. All three parts needed to be changed. Dishwasher now working fine. If your leaking underneath and taking out the dishwasher change those 3 parts.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Timothy from DURHAM, NC
- Parts Used:
- WD15X10014
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set, Wrench (Adjustable), Wrench set
Blocked inlet valve
Removed kick panel and pulled out the unit from cabinet carefully. Turned off water and power. Removed the water feed and used an aluminum pie tin line a low-profile drip pan to catch the extra water and used a scrap towel to clean the dust and extra water spilling out. Used sockets and wrench to remove the old inlet and screwed out the housing to examine the old inlet. No real way to clean it. Honestly, I don’t see a reason for the filter. There’s no way to replace it and it’s not easy to change out anyway. The particles were so small they could have passed through and not harmed the system. A better and more practical place for any filter would be just in front of the inlet that could just pop in every 2-3 years as needed preventatively in 5 minutes. Anyway, I reassembled and tested. Water flow was great. I think it cleans better too because the hot water fills the plastic reservoir faster and stays hot to clean more effectively.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jonni from VACAVILLE, CA
- Parts Used:
- WD28X25960
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
leg fell off of bottom rack.
Slid it in. Very easy and the replacement part is built better than the original part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Suzanne from CHEYENNE, WY
- Parts Used:
- WD12X10109, WD12X10061
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Old parts showing wear
Watched a YouTube video on disassembly, parts replacement, and reassembly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Chris from Medina, MN
- Parts Used:
- WD35X21041, WD35X21041
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Original wheels kept falling off, rack would go off track and it drove me crazy
Simple, took five minutes, no tools, problem solved.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- tim from prior lake, MN
- Parts Used:
- WD12X10163
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The soap dispenser would not close.
This was simple. I took the door apart with a portable screw driver. Then I detached the wires and unscrewed the old module and replaced it. I then put the door back together, loaded the dishwasher and it cleaned my dishes. Even for this `old dog' it was easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wayne from SEASIDE, OR
- Parts Used:
- WD35X21041
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Older wheels had broken clips.
Simply remove broken wheels and clip on replacements. No tools are necessary for this fix and the replacement was inexpensive and easy to install. The kit worked beautifully.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Amelia from PEORIA, IL
- Parts Used:
- WD28X25960
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Rack was rusted and broken.
It was a very simple replacement. I took the old one out and rolled the new one in. It took less than 5 minutes!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michelle from Spokane Valley, WA
- Parts Used:
- WD35X21041, WD35X21041
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The plastic wheels kept falling off the bottom rack of the dishwasher
The old wheels and attachment brackets were easily removed since they were always falling off. I ordered all new brackets and wheels, but it turns out I didn't need new wheels. If your original wheels are in good condition, they are the same size as the new ones and fit the new brackets. The new attachment brackets are built differently than the ones that came with the dishwasher, but (a good thing considering the originals only lasted 1 1/2 years). The new brackets and wheels snapped together and snapped into place on the dishwasher in minutes--no tools were needed. It took longer to cut the parts out of the packaging than to install them. The bottom rack now rolls out like it did when it was brand new. Definitely worth the few dollars in parts.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jean from White Plains, NY
- Parts Used:
- WD12X10122
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
missing cap
I placed the missing cap into the dispenser.
Was this instruction helpful to you?
Thank you for voting!