GDWT608V55BB General Electric Dishwasher - Instructions

Removed screws that held dishwasher under cabinet...pulled out DW...removed old part...replaced with new....easier than falling off a stump.

Repairs do not get any easier than this. Remove 12 screws to disassemble door panel (be careful not to let front panel of assembly to drop or bend when screws release it). Remove 6 screws to remove old detergent dispenser. Unplug cable from old dispenser. Connect cable to new dispenser. Install new dispenser into door with 6 screws and then reassemble door panel with 12 screws making sure to keep all wiring free from pressure points.

Pulled out the old gasket and replaced with the new gasket. Inserted the steel spring clip into the ends of the gasket. Repair complete.

Remove door cover shell by removing screws in inside of door. Unplug harness to control module.Remove outer door shell.Remove four screws at the blower motor. Replace with new motor after disconnecting harness to motor. Reinstall module harness reinstall door shell.

Just have a good look at how the original is installed before removing, then clean the area. The new one was a breeze to install, just line it up and pop it in.

Open the door and go along entire edge of door and use Philipps to unscrew the front panel of the door from the inside panel of the door. Once unscrewed open carefully. There are screws in the dispenser cup. Undo those and then there are two plugs to be undone. There is also the main black computer component that has to be unplugged from its cord. Just remove and screw everything back the way it was. This was my first time and I am a female age 58 years old. It was simple. If I had to do it again I could do it in less than half the time.

I unscrewed the screws in the door of the dishwasher. Then pulled the inside part of the door up and unscrewed the 6 screws that held the dispenser. I am not sure the correct name of the part but it is on the backside of the dispenser and is red and it is where the wires connect to it, that was probably the most difficult part, disconnecting the plastic covers from the old dispenser. I used a butter knife to pop it out and then was able to get a better grip to pull them off. I pushed the wires on the new red thing and then put the new dispenser in place. You have to make sure that the dispenser is in the right spot and the brace on the underside of the inside part of the door, is in the correct place, otherwise, you will have a leak. Which is what happened to me. I just unscrewed and opened it again and screwed the screws tighter and it was fine.

simply removed broken valve and replaced with new valve, easy peasy. shipping was GREAT, Overnight. all in all a easy fix.

I examined how the old gasket was attached before removing it. I then pushed in the new gasket needing no tools. There has been no water leakage since.

Removed the door gasket and cleaned the track prior to installing the new gasket. The online repair instructions didn't mention a thin wire that is stored at the bottom of the tub near the door and is used to hold the ends of the gasket in place. Gently remove the ends of the gasket from the wire prior to pulling the entire gasket out of the machine track.

look at neww part first then r&r

The tub gasket is very easy to replace. First I pulled out the old gasket then using the center marking on the new gasket, I centered the gasket at the top then pushed the gasket into the track. At the bottom I reused the wire that holds the two ends in place making sure I attached the separation wire in the same configuration as with the old one. I had another leaking problem with the seal on the bottom of the door. GE does not sell a repair seal for the door bottom and a new inner door must be purchased at around $200. I made that repair using an old bicycle inner tube. I cut the tube into a one inch strip and epoxyed the strip to the tub where the door meets the tub.. Worked perfectly!

very happy with the product and fast shipping. removed kick plate from dishwasher, inlet valve was on the front left bottom slid out dishwasher removed two screws and disconnected water line,and installed new inlet valve,very simple job if your somewhat handy,make sure you use thred sealant on water line when re installing

I had a small leak from under the dishwasher which turned out to be a tiny hole in the Pump Connector. With the power off I pulled the dishwasher out of the cabinet and disconnected the water and drain lines to give me more room. I put the dishwasher on its back to have access to the pump assembly. A couple of nut drivers and the pump connector is accessible. Replaced the pump connector and over tightened it "Crack"... had to replace the Main Conduit connector ($50). I was able to turn a simple $20 repair into a $70 repair. Now that's talent!

On the Model PDW9880, there are about 14 screws to be removed. I used a large Phillips driver and a pair of needle nose pliers. You cannot use a cordless drill driver for about 10 of the screws unless you have a long bit, as the 10 screws are so close to the body of the dishwasher door that the chuck of the drill will not clear. At the top of the door there are two screws on either side of the latch. The two screws are attached to white plastic blocks that serve as a lip to hold the outer door to the liner. It took a little wrestling with the two plastic blocks to slide them out from under the lip, releasing the outer door. Be sure not to let the outer door drop away, as it will tug on the ribbon cables that connect the display to the dishwasher. Keep a towel or sponge handy to keep the
dishwasher handle from resting on the tile floor. There were 4 electrical connections, including two ribbon cables, both of which just pulled out. I needed a needle nose pliers to remove the 2 spade connectors from the detergent dispenser solenoid, in order to pull on the connector, not tug on the wire. The entire repair is actually pretty straightforward and easy. It took 40 minutes, doing it slowly and carefully. But please don't tell anyone that it is easy, because my wife thinks it was an extremely complex repair, involving the risk of high voltage electricity.

The replacement part fits different makes and models, and does not have any brand identification, other than the Cascade logo cast into the front. Other than that, it appears to be identical to the original. Note: The
soap cup does not open for several minutes in the cycle, so don’t waste time or frustrate yourself (as I did) by checking the dispenser during the first 10 minutes of the cycle. Incidentally, although the company is in Canada, my part shipped from Central California (Fresno) and arrived in the Los Angeles area the next business day.