GDWT368V55SS General Electric Dishwasher - Instructions

Turn off power and water from dishwasher. Remove Base Access Panel. Remove the upper 2 screws that holds the dishwasher in place. Pull out dishwasher. Locate the valve and remove the 2 screws holding the mounting bracket. (I used a hex Nutdriver to remove the screws) Remove the valve. Disconnect the wire connector. Disconnect water supply. (Place a towel to catch the water) Loosen the hose clamp holding the inlet hose and remove the hose. (I used pliers to loosen the clamp) Remove the elbow from the old valve and reattach to the new valve. (Use teflon tape around the threads) Reverse the Process. Check for leaks. Piece of Cake. Part was an exact fit.

No tools required. The seal just pushes into a channel around the tub. The lower ends are held by a wire that spans the lower edge of the door. The center of the gasket is marked to agree the the tub center.l. The seal just pulls out so I removed it and the wire. Cleaned the seal channel and wire and installed the new seal starting at the Top center and working down to. the lower ends are anchored,I found the center of the seal and upper channel and pushed it in place and worked around the corners and down. It took longer to clean the channel and door than to install the gasket.

The first thing I did was watch the video on the removal of the old broken dispenser and I said to myself that it couldn't be that easy. Well I am going on 70 years old and I was going to call a local to fix it. I bought the new dispenser just to avoid the up-charge. When the conformation email got here with video and written instructions. I watched the video and read the instructions. Just after the part arived (ahead of scheduls) I looked at the machins and said wat the he** what is she going to do to an old man. Got my screwdriver (battery and reversable) and wouldn't you know it . It only took me less then 15 minutes to do the whole job. I can't thank them enough for the video. Wife asked where the part was and almost pased out when I opened the door.. lol Trust these people . They know what they are doing!!!

Remove Base Access Panel; Removed Valve Mounting Bracket & Valve; Disconnected Wire Connector; Disconnected Supply Line & distribution Hose; Reversed the Process. Piece of Cake; Part was O.E.M.Component Exact Fit; Took Longer to Write this than it took for Fix. Thanks I Will Be Back for other Parts.!

unscrewed dishwasher from cabinet, then I flipped dishwasher on it's side. loosen pump motor bracket arm on the end of the motor. loosen pump motor to pump conecter hose clamp and then unscrewed pump motor connector from dishwasher. To install I did the reverse. very easy.

Easy repair-removed hex nuts and and screws to pop out old part and replace with new one. New part works better than the original! 1st replacement part arrived with a broken piece, a quick, courteous phone call got a replacement sent out. It took a 2nd phone call to obtain the refund, but the customer care reps are efficient and friendly. I would order from them again for positive service reasons alone.

Inserted new cap purchased from PartSelect.

I watched the video that came with email on part. Gave instructions on how to. Thank you !

Ordered most likely part...water inlet valve.

1. Turn off water supply.
2. Remove the metal toe kick plate/insulation at the bottom of the
dishwasher.
3. Remove hose to supply valve.
4. Take electrical plug off old valve.
5. Remove float valve because it was mounted it right in the way of
the 2 screws on the inlet valve bracket.
6. Remove those 2 screws now you can get to them, and move the
inlet valve to one side so you can get to the hose clamp for the
rubber hose out of the valve going to the dishwasher.
7, Take the old valve and bracket out, mount new valve on the
bracket, crawl back down on the floor, reinstall rubber hose and
bracket, and float valve and finally inlet hose.
8. Turn water on. Check hose connections for leaks. Yep, outlet
hose didn't clamp enough now, allowing a drip.
9. Repeat the whole process AGAIN. Replace little clamp
with a REAL hose clamp, reinstall the thing again. No leak this
time.
10. Test run dishwasher thru a cycle. Check again for leaks at hose
connections. OK ? Reinstall insulation pieces and toe kick
plate.

followed the video step by step which was very well expalined and was able to complete the install

Put new basket in, threw old one away

Watched online video, repaired myself in under 10 minutes.
Easy fix with video instructions

Ordered new cap and put it on when it arrived.
Simple

I placed the missing cap into the dispenser.

This was simple. I took the door apart with a portable screw driver. Then I detached the wires and unscrewed the old module and replaced it. I then put the door back together, loaded the dishwasher and it cleaned my dishes. Even for this `old dog' it was easy.