GDWT166V50SS General Electric Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- GEORGE from LEVITTOWN, PA
- Parts Used:
- WD15X10014
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
Water leak under Unit
Remove Base Access Panel; Removed Valve Mounting Bracket & Valve; Disconnected Wire Connector; Disconnected Supply Line & distribution Hose; Reversed the Process. Piece of Cake; Part was O.E.M.Component Exact Fit; Took Longer to Write this than it took for Fix. Thanks I Will Be Back for other Parts.!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carri from Louisville, KY
- Parts Used:
- WD12X10163
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
latch on detergent assembly broken off
Easy repair-removed hex nuts and and screws to pop out old part and replace with new one. New part works better than the original! 1st replacement part arrived with a broken piece, a quick, courteous phone call got a replacement sent out. It took a 2nd phone call to obtain the refund, but the customer care reps are efficient and friendly. I would order from them again for positive service reasons alone.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from LAS VEGAS, NV
- Parts Used:
- WD15X10014
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Wrench (Adjustable)
Valve leaked
Turn off power and water from dishwasher. Remove Base Access Panel. Remove the upper 2 screws that holds the dishwasher in place. Pull out dishwasher. Locate the valve and remove the 2 screws holding the mounting bracket. (I used a hex Nutdriver to remove the screws) Remove the valve. Disconnect the wire connector. Disconnect water supply. (Place a towel to catch the water) Loosen the hose clamp holding the inlet hose and remove the hose. (I used pliers to loosen the clamp) Remove the elbow from the old valve and reattach to the new valve. (Use teflon tape around the threads) Reverse the Process. Check for leaks. Piece of Cake. Part was an exact fit.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jerome from Arlington, VA
- Parts Used:
- WD12X10122
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Lost Rinse Aid cap
Inserted new cap purchased from PartSelect.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from Denvr, CO
- Parts Used:
- WD12X10122
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Dispenser Cap Missing
Ordered new cap and put it on when it arrived.
Simple
Simple
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Darrell from WAHPETON, ND
- Parts Used:
- WD35X21041
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Bottom dish rack would not roll in and out because several wheels were off because of broken axles. It had to be lifted to get in and out which resulted in many chipped and broken dishes.
I removed the bottom rack from dishwasher. Took off the wheels with the broken axles. Put the new axles on the new wheels and slipped them on the rack. They fit perfectly and rack now glides in and out smoothly. Easy as pie, and took less than 10 minutes. Parts arrived in just two days. Thanks for the great service.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Melissa from WARNER ROBINS, GA
- Parts Used:
- WD35X21041
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Dishwasher not cleaning properly
The kit came with the anchors and the riollers for the bottom shelf. They clipped right on! Dishwasher cleans great now!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marilyn from CALDWELL, ID
- Parts Used:
- WD35X21041
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Needed to replace rollers on bottom dishwasher rack
Pulled off old rollers and snapped on new ones. Never easier!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- REVERIE from HAMPTON, VA
- Parts Used:
- WD35X21041
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
lower rack wheels kept falling off
delivery of part was very quick, and my husband was able to remove the old part and install the new in about 10 minutes. No service call; no new rack; just a washer that is easy to use again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alyce from DIX HILLS, NY
- Parts Used:
- WD35X21041, WD28X10128
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Wheels kept coming off
Wheels and axles come separately and no instructions were included. After a few minutes of looking at the parts, I realized you have to put the axles on the wheels and then snap it on the dish rack. Once I did the first one, the others were easy. Made my dishwasher feel like it was new. Obviously the design of the original wheels was faulty as these were a different design.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barry from FISHKILL, NY
- Parts Used:
- WD35X21041
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
one old roller broke
pulled off all old rollers and axiies and snapped on new ones
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DENNIS from MAUMEE, OH
- Parts Used:
- WD12X10163
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Rinse cap was broken
Watched online video, repaired myself in under 10 minutes.
Easy fix with video instructions
Easy fix with video instructions
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jimmy G from SPRING, TX
- Parts Used:
- WD15X10014
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
Water leakage at valve
I watched the video that came with email on part. Gave instructions on how to. Thank you !
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lisa from CHARLOTTE, NC
- Parts Used:
- WD35X21041
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The rollers on the bottom rack of my GE Monogram Dishwasher all broke and melted so opening and closing the rack was extremely difficult!
It couldn't have been easier. I installed the new wheels in seconds and the rack glides as perfectly as the day it was installed 11 years ago! Perfection! Your stellar website made it so easy to find the correct parts. BRAVO!!!!! I laughed! I cried! I am so ECSTATIC!!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alice from BLAINE, MN
- Parts Used:
- WD12X10122
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
cap had melted mi
Unscrew the old one and screw in the new one.
Was this instruction helpful to you?
Thank you for voting!