GDWF100V55WW General Electric Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- ARTHUR from OAK PARK, IL
- Parts Used:
- WD12X10163
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Pliers, Screw drivers
Detergent dispenser did not work
Followed the instruction video on your website. It was accurate and valid. The repair should have taken 15 mins., instead one of the screws holding the dispenser was frozen. Tried DW-40, and liquid wrench. Neither worked because the screw was in plastic.Finally got out the Dremel and cutting wheels. Had to cut away enough of the unit until I could get at the screw (it was the center bottom one). Sliced through some more of the housing, then cut a notch in the screw head deep enough so I could apply enough pressure with a flat blade screwdriver to open it. After that things went as smoothly as could be expected.A bad design and cheap materials.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kenneth from Dublin, OH
- Parts Used:
- WD12X10163
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Old soap dispensor latch would not hold
Turned off the power at the main box. Removed the six phillips screws and two bottom hex screws holding the front panel. Removed the two solenoid wires on the old dispenser (Label wire polarity). Removed the eight screws holding the old soap dispensor and took it out. Cleaned the area around the hole. Laid down a bead of silicon caulk around the hole edges. Placed the new dispenser in the hole and replaced the eight screws (do not over tighten). Replaced the two wires on the dispenser solenoid (check polarity). Replaced the front cover (Do not over tighten. Turned on the power and job complete.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Laura from Waunakee, WI
- Parts Used:
- WD35X21041
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Wheels on lower unit kept falling off.
I simply removed the old (broken) stud rollers by pinching them with a needle nose pliers and pushing them out, snapped the new stud roller in the wheel, and snapped the wheel onto the lower basket unit. If you have all of the wheels and they are in good shape, you do not need to buy new wheels, the new stud rollers work just fine with the old wheels.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Magnolia, TX
- Parts Used:
- WD35X21041
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Basket Wheels Were Falling Off
This was a simple part swap. The stud rollers are the small peg-clips that hold the wheel on the lower dish rack. Removing the old stud rollers from the wheels required a pair of pliers. I then popped the new stud rollers into the old wheels and snapped them back onto the lower dish rack. I scored some major points from my frustrated wife -- easy, fast fix!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- SUSAN from LAKE FOREST, CA
- Parts Used:
- WD35X21041, WD35X21041
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Wheels became loose
Really all it took was removal of the old wheels which would not stay on anyway and the installation of the new ones. That required the axle and wheel being put together and the installing both of those on the lower rack. I was about to buy a new dishwasher when the salesmen told me about a product called Lemi Shine it saved my hundreds of dollars and the inside of my dishwasher looks brand new. With my new wheels I am good to go again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Virginia from Princeton, NJ
- Parts Used:
- WD35X21041
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The axxle for the wheels were worn out causing wheel to rotate inward and the tray to be to low in the dishwasher.
Simply pull out the old axle and snap in the new one. It is simple. Also the replacement axels were MUCH better quality than the originals. The bottom tray now slides in and out very easily. Note, if you have this problem, you do not need to replace the wheel, just the axle.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eric from Raleigh, NC
- Parts Used:
- WD35X21041
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
wheel fel off bottom tray
but axle on new wheen and put axle on tray
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Lakewood, NJ
- Parts Used:
- WD35X21041
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Wheels on lower basket kept falling off, axel worn out.
Removed empty basket from dishwasher. Placed basket upside down and removed remaining wheels from basket by detaching worn axel from attachment points. ie, No tools needed for this procedure. Once axel and wheels were removed, I squeezed the end of the old axel with needle nose pliers or regular pliers to relieve the outward pressure and pushed the old axel out of the wheels. Easy, popped right out.
Positioned new axel against the outer wheeel hole and applied thumb/finger pressure to snap in new axel. Took the wheel with the new axel and
attached it to the basket at the original position. New axel grips the basket like a clothes pin would.
Continued and replaced all eight axels at this time.
Replace basket in machine, stand back and admire work and parts!!!! Parts received promptly with no hassels. Excellent company to do business with, clear photos and ordering forms.
Will definately re order again if needed. Thank You.
Positioned new axel against the outer wheeel hole and applied thumb/finger pressure to snap in new axel. Took the wheel with the new axel and
attached it to the basket at the original position. New axel grips the basket like a clothes pin would.
Continued and replaced all eight axels at this time.
Replace basket in machine, stand back and admire work and parts!!!! Parts received promptly with no hassels. Excellent company to do business with, clear photos and ordering forms.
Will definately re order again if needed. Thank You.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from TAMPA, FL
- Parts Used:
- WD35X21041
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Old rollers broken
No instructions. At first thought I needed instructions. A minute later I was attaching the new rollers. Simple and easy. Took less than 15 minutes. Would recommend these rollers.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Newport Coast, CA
- Parts Used:
- WD35X21041, WD35X21041
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
wheels were broken and had fallen off rack wouldnt roll
We received our parts for our dishwasher within 2 days. It was very simple to find the parts on your site, and very easy to install. Our dishwasher is back to normal and the racks roll in and out easily. I would recommend ordering from PartSelect to anyone.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Randy from Placentia, CA
- Parts Used:
- WD35X21041
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Bottom dish basket would not roll in and out. Wheels were falling off.
Removed the existing stud rollers with the wheels attached. Then removed the wheels from the stud roller. Then snapped the wheels on the new "Better Designed" stud rollers. Then easily snapped the new stud roller assembly in place. Piece of cake...works like a charm.
Thanks,
Randy
Thanks,
Randy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from HAVERHILL, MA
- Parts Used:
- WD15X10014
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
Leaking valve
Used teflon tape around new 3/8 elbow. Re-installed valve in originals postion. Connected supply hose and reconnected electrical to valve.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Prasad from LEAWOOD, KS
- Parts Used:
- WD21X10169
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
Dishwasher was not starting
Replaced interlock assembly as one of the possible causes. The replacement was easy, but this was not the final fix. I also replaced the water inlet valve, flood switch and finally found that there was large calcification within the drain tube assembly (not visible, but was blocking water). Got a new flexible tubing and new drain hose, plugged everything together and the dishwasher runs like new now. Watching for a potential leak from the drain tube to drain hose connection and mya need to tape it up, but so far so good...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Virgil from NAPERVILLE, IL
- Parts Used:
- WD30X10039
- Difficulty Level:
- Difficult
- Total Repair Time:
- More than 2 hours
An old inner rail fell apart and needed replacing
I repaired by replacing both inner rails.
I found that removing an inner rail from the rack is difficult. It can be done with strong fingers separating the tabs of a front Y hook after releasing the rear hook so the rack can slide off the horizontal locator rods. It helps to apply liquid soap to the old inner rails Y clips to reduce friction.
Clean the outer rails thoroughly with a brush and liquid cleaner so the rails can engage
Inserting the inner rails into the outer rails is difficult when they are already attached to the rack. It's much easier to insert the rails independently of the rack. Push the outer rails into the inner rails while applying force to keep them engaged
Attach the rack to the rails by inserting the long rear horizontal rods of the rack into the rear clips of the rail.
Assure the tabs in the rear clips are locked
Again, it helps to apply liquid soap to the new inner rail Y clips to reduce friction
Hold the rails in place and pull the rack forward to engage the front rails with Y clips to the shorter front horizontal rods of the rack.
Force them together to spread the Y clips and lock the rails into them.
I found that removing an inner rail from the rack is difficult. It can be done with strong fingers separating the tabs of a front Y hook after releasing the rear hook so the rack can slide off the horizontal locator rods. It helps to apply liquid soap to the old inner rails Y clips to reduce friction.
Clean the outer rails thoroughly with a brush and liquid cleaner so the rails can engage
Inserting the inner rails into the outer rails is difficult when they are already attached to the rack. It's much easier to insert the rails independently of the rack. Push the outer rails into the inner rails while applying force to keep them engaged
Attach the rack to the rails by inserting the long rear horizontal rods of the rack into the rear clips of the rail.
Assure the tabs in the rear clips are locked
Again, it helps to apply liquid soap to the new inner rail Y clips to reduce friction
Hold the rails in place and pull the rack forward to engage the front rails with Y clips to the shorter front horizontal rods of the rack.
Force them together to spread the Y clips and lock the rails into them.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Samuel from LAS VEGAS, NV
- Parts Used:
- WD14X10009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Hinge arm link wore out
Used Phillips screwdriver to undo brackets that keep dishwasher in place. Pulled out dishwasher from underneath the counter. Placed hinge arm in spring, hooked spring onto clip, placed hinge arm in clip. Put back dishwasher under the counter and screwed in place. Took all of 15 minutes. Saved 185.00 for service call.
Was this instruction helpful to you?
Thank you for voting!