GDT720SGF0WW General Electric Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- louis from ROCKTON, IL
- Parts Used:
- WD28X20164
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Lower rack was broken/ rusted
Just snap part in position quick to do.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marlene from FT WASHINGTON, MD
- Parts Used:
- WD35X20794
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
new dishwasher with broken upper spray arm
The part did not fit at all but not worth it to me to return it. The part I need is about 20 inches in length and the one sent was about 10 inches. I will simply call for this dishwasher to be repaired or replaced.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Julian T from Dalton, GA
- Parts Used:
- WD01X35298
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
roller wheel was melted.
I removed the old roller wheels and the new roller wheels snapped together and the simple instructions made the repair quick and simple..
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cody from Denver, CO
- Parts Used:
- WD30X20110
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Guide Rail for Rack Broke
I determined the guide rail on one side had broke when the white plastic bearings fell out of their track. I decided to replace both sides at the same time, so I ordered 2. They arrived quickly and I installed them and placed the middle rack back into the dishwasher. Went together fairly easily. I took pictures before removing the guides from the rack, so I would remember how to put the new ones back one when they arrived. Very happy with this DIY repair that easily would have taken much longer and would have been way more expensive! Thank you!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from JUNCTION CITY, OR
- Parts Used:
- WD15X26140
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Wrench set
No water getting to the dishwasher
Researched what others have posted about on Parts select. That really helped with the diagnosis! Took a chance on a $28 part. Repairman was going to charge $150 just to show up, then diagnose, leave for 2 months while waiting for the part, charge another $150 plus the part to fix…
Just had to pull out dishwasher far enough to take the water supply line off. Then the water inlet solenoid then 2 more screws and a 2 pronged plug reattach water supply then done! 15 minutes MAX!!!
Just had to pull out dishwasher far enough to take the water supply line off. Then the water inlet solenoid then 2 more screws and a 2 pronged plug reattach water supply then done! 15 minutes MAX!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Drew from ROACHDALE, IN
- Parts Used:
- WD28X34743
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Old bottom dishwasher rack had rusted prongs and a few had broken off.
Bottom rack came complete with all racks. Only had to transfer the (2) side bumper guards,
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Andrew from WINONA, MN
- Parts Used:
- WD28X35779
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Old rack had rusted and broken tines
1. Take a picture of the old rack in the dishwasher! Just in case!
2. Remove rail channel end caps and place them on the tabletop on the correct side to make sure you put them back on the correct side.
3. Remove old rack.
4. Carefully snap off the water sprinkling unit. (carefully push down tabs so they don't break).
5. Using your picture as a reference (!) snap the water sprinkling unit on the new rack (it's easy).
6. Put the new rack back onto the rail channel and replace the end caps.
Done! Very easy installation ! Rack was not nearly as expensive as I anticipated and was delivered quickly. Note: You get the rack only. All ot the other parts are from the old unit.
2. Remove rail channel end caps and place them on the tabletop on the correct side to make sure you put them back on the correct side.
3. Remove old rack.
4. Carefully snap off the water sprinkling unit. (carefully push down tabs so they don't break).
5. Using your picture as a reference (!) snap the water sprinkling unit on the new rack (it's easy).
6. Put the new rack back onto the rail channel and replace the end caps.
Done! Very easy installation ! Rack was not nearly as expensive as I anticipated and was delivered quickly. Note: You get the rack only. All ot the other parts are from the old unit.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from OMAHA, NE
- Parts Used:
- WD28X35779
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Upper rack rusted out
Took out the old and swapped out the parts from the old one and put them on the new rack. Looks great and works great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from DANBURY, CT
- Parts Used:
- WD21X10519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
Ge Dishwasher was not filling with water
I replaced the Flood Switch Part Number: WD21X10519.
I found that be removing the bottom front cover under dishwasher door, there was a small black plastic clamp holding up the wiring cable. By disconnecting the clamp, it gave me a few more inching of wire inside the machine, which made disconnecting old flood switch easier. It also help in installing the new flood switch. Then finally i reinstall the clamp cable under the machine to finish the job.
I found that be removing the bottom front cover under dishwasher door, there was a small black plastic clamp holding up the wiring cable. By disconnecting the clamp, it gave me a few more inching of wire inside the machine, which made disconnecting old flood switch easier. It also help in installing the new flood switch. Then finally i reinstall the clamp cable under the machine to finish the job.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- GARY from SOAP LAKE, WA
- Parts Used:
- WD12X32798
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
The soap dispenser was broken os to save money I ordered one on-line
The repair instructions were great and the repair went well. The repair took less than an hour.
Thank you
Gary
Thank you
Gary
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Teresa from DETROIT, MI
- Parts Used:
- WD21X10519
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
Dishwasher did not dry dishes
Followed directions on YouTube
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Francesca from PALM COAST, FL
- Parts Used:
- WD28X35779
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Rusty upper rack
I simply followed the video instructions and replaced the rack myself, no tools required. Easy peasy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Emilene from BRENTWOOD, CA
- Parts Used:
- WD28X20163
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Tine on lower rack broke
Just snapped it in place and that’s it!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- PRAVEEN from MONROE TWP, NJ
- Parts Used:
- WD28X35779
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Rusty DW Baskets
the part is OEM and fits like a glove. No worries. There is a minor variation in design and is not like for like design but fits exactly per specs and works. I have been looking for this part for years now. Thank you for PS for maintaining the inventory.
PS12743260Manufacturer Part Number WD28X26099
PS12743260Manufacturer Part Number WD28X26099
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dirk from HAYDEN, ID
- Parts Used:
- WD22X22857, WD22X22853, WD35X20794, WD03X20446, WD21X10519, WD21X10494
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers
Water not heating and door would fall when opened
Watching u tube. Made it simple
Was this instruction helpful to you?
Thank you for voting!