GDF570SSF0SS General Electric Dishwasher - Instructions

Drain hose elbow (#326) had a crack in it. Disconnected power, slid dishwasher out and laid on its back. Hose had two pinch clamps to remove. Replace old hose with new one and used standard hose clamps. Put dishwasher back in place and hooked power back up. Entire process took less than 30 minutes. PartSelect had elbow for about $6. GE does not sell just the elbow. They sell whole pump setup for about $106.

Took off the door and separated the two door pieces. Unscrewed the old dispenser and replaced it with the new one.

Put new basket in, threw old one away

I tested Heating Element with Ohm Meter-Direct Short (if open it would have been bad and I would need to replace the element. Per the Website Troubleshooting for GE dishwasher, it said Heating Element (65%), Float Switch (32%), or Computer Board (only 3% Chance of it being board). So I ordered Float Switch. Later I noticed that the dishwasher would not change wash cycles from Heavy, Normal or Light.
So I turned the Circuit Breaker on and off. This fixed the Wash Cycle.
When the Float Switch Came in, I installed it in a few minutes watching the video on the GE Troubleshooting Page. Later when it was running I checked the operation and when I opened the door, the wife says seeing the steaming water, You fixed it, the Water is Hot now ! It was all about Hot Water, not the Heating Element at all ! And I think everything was fixed when I flipped the Circuit Breaker on and off and re-set the computer board. I think replacing the Float Switch was good maintenance, cause it was really dirty and needed to be replaced soon anyway. And it may have avoided my wife's next misdiagnosis with our dishwasher. This was 2 weeks ago, and all is well.
Sincerely,
Scott

Opened the box took the rack out and placed it in the dishwasher. Good as new.

Replaced all 3 spray arms in less than 10 minutes.The top one came in two pieces,the mounting bracket and the arm.Snap the bracket on the dishwasher first , then attach the arm to the bracket.

This is NOT a complaint about Parts Select (GE however has some packaging issues to resolve). It may become a complaint of Parts Select if not resolved to my full refund.

Unable to repair with provided part.

I have performed this repair in the past easily and successfully with part from GE Parts. GE Part Number: WD18X10052

GE Parts currently lists part number above as discontinued with a new GE Part
Number: WD35X10386. However not in stock

Found new part number locally however was missing the hose and plastic molded tubing that connects to pump and provides the actual diverter mechanism. Obviously did not purchase.

Ordered from Parts Select on 2021-12-22 and inquired if their part was complete. I was assured it was and paid for overnight shipping at approximate cost of $30.

Part arrives on Christmas Eve, a day late and incomplete. Called Part Select and was assured I would be reimbursed for full cost of part and shipping and was provided with shipping label to return incomplete part at their cost once their stock personnel verifies my claims.

I have photos of original/damaged but complete part beside new in package incomplete part for record and your use if you request.

Email Greg at:
One_US.Marine@yahoo.com

Researched what others have posted about on Parts select. That really helped with the diagnosis! Took a chance on a $28 part. Repairman was going to charge $150 just to show up, then diagnose, leave for 2 months while waiting for the part, charge another $150 plus the part to fix…
Just had to pull out dishwasher far enough to take the water supply line off. Then the water inlet solenoid then 2 more screws and a 2 pronged plug reattach water supply then done! 15 minutes MAX!!!

Followed the instructions on the video, it was pretty straight forward. It was helpful to know what to expect before hand like removing accumulated water in the drain before removing the flood switch so as not to have that water drain under the dishwasher. Knowing to have a nut driver with magnetic tip was helpful in removing and reinserting the screws. all in all it was pretty easy repair.

Had to trouble shoot to isolated the true fault condition. Checked heating element was good
Researched symptoms on YouTube
Removed and inspected float switch part
Ordered and replaced part.

I removed the old roller wheels and the new roller wheels snapped together and the simple instructions made the repair quick and simple..

I determined the guide rail on one side had broke when the white plastic bearings fell out of their track. I decided to replace both sides at the same time, so I ordered 2. They arrived quickly and I installed them and placed the middle rack back into the dishwasher. Went together fairly easily. I took pictures before removing the guides from the rack, so I would remember how to put the new ones back one when they arrived. Very happy with this DIY repair that easily would have taken much longer and would have been way more expensive! Thank you!

The part did not fit at all but not worth it to me to return it. The part I need is about 20 inches in length and the one sent was about 10 inches. I will simply call for this dishwasher to be repaired or replaced.

I followed the U tube instructions already put out part select.

Looked upm the problem it said door wasn.t closed so cause was the door latch. put in the new one no change so I bought a new dishwasher