GDF570SSF0SS General Electric Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Larry from HAMBURG, PA
- Parts Used:
- WD08X23476
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Bad tub gasket
Thanks to this site for saving me about 150.00.This is my third repair with parts from your company. Thank you.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Scott from FOUNTAINTOWN, IN
- Parts Used:
- WD15X26140, WD21X10519
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
No water
Turn off water supply, turn of power to dishwasher, remove mounting screws, slide dishwasher out of opening, place a pan under water supply valve, remove water line, remove screws holding the valve in place, disconnect electrical connector. Reverse process to install new valve.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bernard from CLAYTON, NC
- Parts Used:
- WD21X10519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Unit wouldnot drain
Removed the screen cover and then removed two bolts with nut driver and removed white plastic retaining piece. Pulled flood switch out of housing (raise approximately 2 inches) then unfasten electrical plug. New part connects to electrical plug (pnly can fit one way so no problem with orientation). Pushed floid switch bsck into lace and attached white plastic retainer with two bolts and then set screen cover back. Very simple and easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeffrey from BENNINGTON, VT
- Parts Used:
- WD15X26140
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
No water
just bolted on the new one and hooked up the hose
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jason from WESTON, WV
- Parts Used:
- WD21X10519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Dishwasher would not receive water when started
The service lady looked up possible trouble items and narrowed it down to the flood switch. Being the most likely cause, I ordered a new one. I removed both trays, the lower sprayer, and both screens. The flood switch has an electric plug on the bottom of it that just pulls off. Just as with other appliance repairs, I actually got the old flood switch to work again before trying the new one. I should have tried to free up the float before ordering the new one. But in case this happens again, I’ll just put the new one in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Susan from STATEN ISLAND, NY
- Parts Used:
- WD08X23476
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
tub gasket was damaged
damage to gasket (had a slit in the area of the utensii baskets.
causing lower right corner of gasket to come out. caused leakage to floor from the lower right corner of door...
As I am 77 yrs of age I was leary of diy but thanks to the reps of
"Parts Select" I actually was able to put in the new gasket myself.It did take some time and lots of patience as it had to be seated correctly..I also had to make sure the new gasket was in the groove as it is supposed to be.
causing lower right corner of gasket to come out. caused leakage to floor from the lower right corner of door...
As I am 77 yrs of age I was leary of diy but thanks to the reps of
"Parts Select" I actually was able to put in the new gasket myself.It did take some time and lots of patience as it had to be seated correctly..I also had to make sure the new gasket was in the groove as it is supposed to be.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Missy from BOWDLE, SD
- Parts Used:
- WD13X10071, WD21X10490
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
dishwasher would not start
I watched a step by step video provided on the Fix It app. Easy to follow directions and only took minutes to tear apart and put back together. Didn't even require help from my husband. Although the latch and striker were not the problem, contacted parts select and they then recommended the electronic control board, they ordered it, had it shipped to me within a few days, another really easy fix I did using the You tube video. Fixed the problem lickety-split. I will never go without my fix it app. Entered all my appliances. Sure beats spending hundreds on appliance repairmen! Thank you Parts Select!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Susan from ATASCADERO, CA
- Parts Used:
- WD28X26099
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Lower dish rack assembly plastic had melted through to the metal
Simple! I removed the flatware tray and pulled out the old rack assembly. Rolled in the new one and replaced the tray. Not really a "repair" per se but a needed replacement.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- CURT from SHELBY TWP, MI
- Parts Used:
- WD28X26099
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Lower dish rack rusted out
Took it out of the box and set rollers on track
rolled in place ALL DONE
rolled in place ALL DONE
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from CROSSVILLE, TN
- Parts Used:
- WD13X10071, WD21X10490
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
Dishwasher won't start.
Nightmare!!! The Striker latch did not pop out with a screwdriver as it was supposed to. The whole dishwasher needs to be disconnected and pulled out, then front door removed and totally disassembled to remove the screw to replace the striker latch. lots of work to replace a striker latch. Bad design!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- PeggyAnn from EAST DUBLIN, GA
- Parts Used:
- WD13X10071, WD21X10490
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
broken latch
My son did the repair, I ordered both latch and striker, only needed the latch...only took him a few minutes to remove the old and install the new and works just fine
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward from BEAUFORT, SC
- Parts Used:
- WD21X10490
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Wouldn't start, no lighted functions.
Shut off power at breaker, remove two screws anchoring DW to counter top . Slide DW out far enough to access door latch, disconnect electrical wiring plug, remove two Phillips head screws, install new door latch, repeat installation in reverse order.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mike from WADSWORTH, OH
- Parts Used:
- WD49X24057
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Old filter had calcium deposits that would not come off with soaking and scrubbing. That restricted water flow.
Simply twist on the new part/filter.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sau from NILES, IL
- Parts Used:
- WD15X26140
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Socket set
Dishwasher would have water left inside over a few days
Repair was straightforward. You can change water inlet on this model from underneath in bottom from, although it is a little tight
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from TIONESTA, PA
- Parts Used:
- WD12X32798
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Socket set
Soap dispenser would not function, wouldn't open.
Took cover of door off. Removeddoor from frame 1st. Lift door off of hinge. Disconnect door from springs. Unscrew bottom screws at base of door. Lift front cover(actually slides down) remove old part replace with new.make sure unplug door from main body.
Was this instruction helpful to you?
Thank you for voting!