GDF570SGD0BB General Electric Dishwasher - Instructions

Dishwasher is under 2yrs old and suddenly failed to drain due to the drain pump not working. I read the reviews on how easy it was to change and went ahead and purchased one. After removing the screw from the appliance bracket under the counter and the two screws from the base plate, it was easy to pull the dishwasher from under the counter and away to flip to its side. I would recommend draining the drain hose first and making sure no water is in the tub. Keep a towel nearby. Removing the drain pump was simple. I needed a nose tip pliers to remove one of the hose clamps and a screwdriver for the other clamp. Once the pump was removed, I opened the old pump by twisting the top part while pressing the tabs to remove upper housing. There was a broken piece of glass that had wedged itself in the mechanism which prevented the pump from working. I wish I had checked that first, before purchasing a new drain pump. I kept the old pump as a backup for the future. It took no more than 20 minutes to get the pump replaced and the dishwasher back in place. Dishwasher drains just as new. By the way, costed under $100 with delivery. An appliance repair company wanted $250!!
Not the first time PartSelect saved me money and won’t be my last!

The lower tray was simple. Lifted the old one out and placed the new one on the lid of dishwasher.

Upper tray: Used the closed point of scissors to gently push the little piece of plastic on the slide and removed the cap on each slider. Pulled the damaged tray off of the sliders. Removed the piece that shoots the water onto the dishes and placed it on the new tray. Put the tray back on the sliders and replaced the little caps back onto the slider so that the tray did not come off of the track. Voila!!

The service lady looked up possible trouble items and narrowed it down to the flood switch. Being the most likely cause, I ordered a new one. I removed both trays, the lower sprayer, and both screens. The flood switch has an electric plug on the bottom of it that just pulls off. Just as with other appliance repairs, I actually got the old flood switch to work again before trying the new one. I should have tried to free up the float before ordering the new one. But in case this happens again, I’ll just put the new one in.

The replacement of the parts was simple enough, but the board appears to need a jumper which was not in the original board.

The start button works, but beeps three times and doesn’t start the washer

I did not do repair. I originally tried to order part from GE. They informed me I had to buy the whole door to replace the bottom door seal. I then looked at Part Select and they had the exact schematic as GE except showed the seal. I called and sales person assured me it was the part I was looking for. My dishwasher. What they didn’t tell me was that seal is riveted to the door. I ended up throwing away the part as it was more expensive to return it . SonPart was a total waste..

Turned off pier at breaker. Removed dishwasher from under counter after disconnecting water line from dishwasher and drain tube from under sink. You might get a little residual water but not much. Removed old flood switch took about 2 minutes. Replaced with new flood switch. Then tilted dishwasher back to get to plastic nuts that hold down heating element. Set unit back down and removed old heating element then replace it with new one. Replace plastic nuts that hold element. Exact parts makes job easy. Them put water hose back on an put washer back in place hooked drain hose back up. Turned water and power back on. Tested unit worked perfectly. Hardest part of job was putting the dishwasher back into counter and getting the Instalation back on top.
Parts replacement time was about 10 minutes.
Disconnecting and reconnecting and replacing dishwasher 40 minutes. But I wouldn’t pay anyone to do this because it’s really not difficult.

Had to remove the rubber gasket on the new spray arm to install the device, as it was hard to push into the above slot that fits the arm..

Simply put it on and twist it to lock in place. Took all of 3 seconds

took out old and replaced with new

Simple! I removed the flatware tray and pulled out the old rack assembly. Rolled in the new one and replaced the tray. Not really a "repair" per se but a needed replacement.

Repair was simple, lower rack just remove and replaced with out any tools or disassemble required, for the upper rack installation, the end cap need to be removed out of the sliding tracks, slide old rack out and discard, clean the track with a suitable cloth and slide new rack in to the tracks, reinstall the old end caps, as a good preventing measure, order new end caps just in case they are need it if the old ones crack during removal.
save old rollers from old racks for future repairs

Simply pick the basket up to slide wheels onto axles and push in until they lock in place.

Popped the old one off. Popped the new one on. Easy as that.

I took out the old one and simply inserted the replacement. It was an exact replacement part and thus a perfect fit. Dishwasher is working fine now! Cost was around $40 (shipped) which I thought was reasonable.

Simply twist on the new part/filter.