GDF540HGD0CC General Electric Dishwasher - Instructions

Thanks to this site for saving me about 150.00.This is my third repair with parts from your company. Thank you.

Removed original silverware basket from dishwasher rack. Replaced it with new silverware basket. Placed original silverware basket in recycle bin (plastic content). So easy, even my 24 year old son could do it!

damage to gasket (had a slit in the area of the utensii baskets.
causing lower right corner of gasket to come out. caused leakage to floor from the lower right corner of door...

As I am 77 yrs of age I was leary of diy but thanks to the reps of
"Parts Select" I actually was able to put in the new gasket myself.It did take some time and lots of patience as it had to be seated correctly..I also had to make sure the new gasket was in the groove as it is supposed to be.

Repair went fine, getting the right pump was the problem. I started with my local appliance parts house, they ordered part came in 3 days. Upon picking it up I noticed that the pump was shaped slightly different and the electrical hook up was totally different. Asking the parts guy what happened he said they must have sent the wrong pump. Returned it for credit and ordered it again. Four days later the same exact thing occurs. Parts guy credits my account and says better go directly to GE. Wait 10 days for GE, for this part and once again same odd looking pump with wrong electrical plug. My son who is a welder by trade asks me if there is a packet of parts in carton and yes there is. He says that perhaps there is a converter for the electrical. That was the solution no one told us that pump was universal and needed the adapter. Not even the 2 different tecks at first house. Perhaps that should be stated in the part would have saved us tons of time. Thanks D

Replaced heating element. This was the path of least resistance but the problem persisted. I tried resetting the dishwasher but still nothing. My last resort is the circuit board. I checked the relays on the old board and they are fine so it must be something else on the circuit board. The dishwasher is not really that old (4 years) and everything else is fine. Just ordered the board so I really hope this fixes the problem.

*Unplug the dishwasher. My drain hose was long enough so no need to disconnect.
Access the motherboard and found a solid green light. This indicates the motherboard is not communicating with the user interface.

Door removal:
- removed kick plate
-unplugged door wire assembly and wire harness clip
-Unscrewed dishwasher from cabinet and pull dishwasher out about 6 inches
-Detached pulley rope assembly from door hinge
-Open door about 4 inches and pull up and towards me.
-Lay the door down, removed vent cap and four T20 screws from the side bottom, remove two 1/4 inch bolt from each hinge(the hinges have four bolts, but only to need to be removed)
-push up on the plastic inner door from outer door and set aside.
-Unscrew four 1/4 inch bolts holding user interface and unplug wire assembly. (The two middle screws are longer than the two outer screws)
-be sure to ground yourself before touching the new user interface board
-read the instructions for the new interface board clip positions(mine was already position correctly)
-Assemble the door and be sure to connect the wire assembly and harness clip.

First went to U Tube to view installation instructions and location of part. It was fairly easy to replace since I had installed the unit. I was able to move the unit out enough without disconnecting any line since there was enough slack in all three connections, only shut the power off. I did use the new parts even though the older ones were not broken. The nylon pulley wheel had built up with lint causing the cable to come off.

Opened the door, put arm on bottom, slid in and twisted. Very, very easy. The right part means a lot. Thank you very much. “ Ol Stump”.

Dishwasher is under 2yrs old and suddenly failed to drain due to the drain pump not working. I read the reviews on how easy it was to change and went ahead and purchased one. After removing the screw from the appliance bracket under the counter and the two screws from the base plate, it was easy to pull the dishwasher from under the counter and away to flip to its side. I would recommend draining the drain hose first and making sure no water is in the tub. Keep a towel nearby. Removing the drain pump was simple. I needed a nose tip pliers to remove one of the hose clamps and a screwdriver for the other clamp. Once the pump was removed, I opened the old pump by twisting the top part while pressing the tabs to remove upper housing. There was a broken piece of glass that had wedged itself in the mechanism which prevented the pump from working. I wish I had checked that first, before purchasing a new drain pump. I kept the old pump as a backup for the future. It took no more than 20 minutes to get the pump replaced and the dishwasher back in place. Dishwasher drains just as new. By the way, costed under $100 with delivery. An appliance repair company wanted $250!!
Not the first time PartSelect saved me money and won’t be my last!

Chances are your Lower spray arm is worn or jets are off. Replacing this part is very easy. Grab the base of the lower spray arm, twist and pull straight up. Place the new one in and twist lock in place. Repair complete!

I checked all the drain lines and filter for blockage. All looked good. I unplugged the unit and unscrewed the two screws adhereing the dishwasker to the counter. I shopvacced the water out of the bottom of the unit, slid it out, and carefully placed it on its back to access the pump. I unplugged the power to the pump, removed the intake and outake ring fasteners. Carefully removed the pump and inserted the new part, mopping up water as I went. Replace the rings, plugged in power to the pump, righted the unit and put it back. Replaced filter with the one that came with the kit.

The lower tray was simple. Lifted the old one out and placed the new one on the lid of dishwasher.

Upper tray: Used the closed point of scissors to gently push the little piece of plastic on the slide and removed the cap on each slider. Pulled the damaged tray off of the sliders. Removed the piece that shoots the water onto the dishes and placed it on the new tray. Put the tray back on the sliders and replaced the little caps back onto the slider so that the tray did not come off of the track. Voila!!

Simple! I removed the flatware tray and pulled out the old rack assembly. Rolled in the new one and replaced the tray. Not really a "repair" per se but a needed replacement.

After hours looking for problem. I tried cleaning door gasket. Did not stop leak. Looked at lower water spray arm and it was split. It is literally a 2 minute repair to remove and install. Knock on wood, no leaks in the last 10 washes.

took out old and replaced with new