GDF540HGD0CC General Electric Dishwasher - Instructions

Didn't actually do the compete repair but got close. Pulled out dishwasher, disconnected and checked continuity on the existing heating element (about 16 ohms) the new element was also about 16 ohms. This indicates they both were working fine and no need for replacement. Next step would have been to swap the elements would have been simple. Tried to replace main board as well, still not the issue so giving up and replacing the dishwasher. It wasn't the high temp cut off thermostat either incidentally and no error codes in maintenance mode. Check continuity of your existing element before ordering to save aggravation.

Open the washer, remove the bottom dish rack, then twist off the bottom water sprayer. Use a screwdriver to remove the mounting/ stabilizing screws so you can slide out the dishwasher. Close the dishwasher and slide it out. Underneath at the back there are two wires powering the drying element, carefully remove them. Use an adjustable wrench to remove the two plastic mounting nuts for the drying element. Open the washer and remove the old drying element, and insert the new element. Reassemble the dishwasher in the reverse order if disassembly.

I replaced the tub gasket around the door circumference which took less than five minutes to replace. However the problem was replacing the beach gasket that prevents the water from flowing out of the dishwasher tub. The door had to be unhinged from the dishwasher which was unscrewed from the cabinets and brought out from its location. After the door was completely removed it was laid on its front. After removing the door hinges which were secured with just one bolt I tried to slide the back panel off the front panel but without any success. So I had to remove the torn and worn out gasket while working in a tight space. This is where the problem rose because according to installation instructions there are screws supposed to be holding it to the main body frame. However, in my case rivets were used by the manufacture since this was the first time the gasket was being replaced. So I had to use a power tool With a grinding bit to remove the face of the rivets and essentially cut them out to reveal the underlying holes. After this I replace the beach gasket and then used half inch SS Philips bolts and nuts to secure the gasket to the body frame.

1. Turn off breaker supplying power to dishwasher in electrical panel
2. Open dishwasher door
3. Unscrew the screws that secure the dishwasher to the counter.
4. Tip dishwasher forward. Identify the non-functioning door latch. It looks exactly like the replacement. Unclip the wire harness from the door latch.
5. On the inside of the dishwasher, there are 2 screws directly under the door latch. Unscrew them and carefully set aside.
6. Remove old door latch.
7. Set new door latch in place. Holding securely, replace screws removed in step 5. Toward the end they get a little tougher to screw in.
8. Plug wire harness into new door latch.
9. Re-align dishwasher and re-secure to counter in previous position.
10. Test latch to make sure it closes properly.
11. Turn on breaker in electrical panel.
The dishwasher should now function properly.

Slid out old part, slid in new part.

It was a simple as: attach and done!
There is a ring on the part that tightens clockwise to the nipple that sprays out the water that it rests on. Twist clockwise and you are done!
It is a mystery how it was unattached to begin with but not a problem in the end, it was easy to fix!

Thanks for sending genuine GE parts!

Parts Select has excellent video instruction. they are way better than I could describe. the repair went smoothly. the heating element wasn't the issue. and it's may not be yours either. I found that the flood switch was the problem part number PS8690623. It's located under the filter screen in the bottom Yes that long grey plastic thing under the screen. It's held in by two 1/4 inch screws. Use a wet dry vacuum or towels to dry up the water in the sump. ABOVE ALL don't drop the screws. You'll be taking the pump apart if you do. Gently lift out the flood switch. There will be wires plugged into the base. With a flat screwdriver gently pop off the white plug from the green base. The plug only goes on one way reassemble in reverse order.

Unplugged the dishwasher and turned off the water. In order to pull the dishwasher out I had to remove disconnect the waterline. Opened the dishwasher door to remove the screws attached under the counter holding the dishwasher in place. Once removed I pulled the dishwasher out of the under counter pocket far enough that I could access the rear connections to the heating element. Carefully disconnected the wires connected to the heating element and then loosened the large nuts securing the heating element. Once the nuts were removed I disengaged the element from the holders and removed it from the dishwasher. Installed the new element in place engaging it into the holders inside the dishwasher. Then moved back to the rear of the dishwasher installing the nuts that were removed earlier on the new element and reconnected the cables.

I ordered my new heating element prior to checking the continuity of the old one. I checked the continuity of the old one once it was removed and it was ok, not great but still acceptable so I knew the new element wasn't going to fix the issue, but installed it anyways. My issue was actually the float switch, so if you want to be sure of your issue, remove the current heating element from your dishwasher and check the continuity before ordering if you want to save some money.

Opened door slid in new rack, came with wheels

The part simply snapped in and worked perfectly.

Replaced bad roller carrier with a new one.

Shut off power at breaker, remove two screws anchoring DW to counter top . Slide DW out far enough to access door latch, disconnect electrical wiring plug, remove two Phillips head screws, install new door latch, repeat installation in reverse order.

There was no repair -- it was a simple snap-in replacement of lower spray arm assembly. The shaft holding the lower spray arm in place is plastic so of course it broke when a utensil blocked the arm from spinning.

I appreciate the Parts Select company for enabling me to purchase a replacement part though that allows me to keep my old dishwasher working.

Removed old spray arm. Installed new one. New model spray arm doesn’t need metal heat shields.

Repair went fine, getting the right pump was the problem. I started with my local appliance parts house, they ordered part came in 3 days. Upon picking it up I noticed that the pump was shaped slightly different and the electrical hook up was totally different. Asking the parts guy what happened he said they must have sent the wrong pump. Returned it for credit and ordered it again. Four days later the same exact thing occurs. Parts guy credits my account and says better go directly to GE. Wait 10 days for GE, for this part and once again same odd looking pump with wrong electrical plug. My son who is a welder by trade asks me if there is a packet of parts in carton and yes there is. He says that perhaps there is a converter for the electrical. That was the solution no one told us that pump was universal and needed the adapter. Not even the 2 different tecks at first house. Perhaps that should be stated in the part would have saved us tons of time. Thanks D