GDF520PGD0BB General Electric Dishwasher - Instructions

Shut off power at breaker, remove two screws anchoring DW to counter top . Slide DW out far enough to access door latch, disconnect electrical wiring plug, remove two Phillips head screws, install new door latch, repeat installation in reverse order.

Replaced bad roller carrier with a new one.

Dishwasher would not activate heating element to dry dishes, but element still has continuity. Determined main board was not supplying voltage to element. Remove front cover, disconnect power leads, disconnect and then drop down main board (held up by two screws). Reverse to install. Unfortunately the main board didn't correct the problem. It's not the thermostat either and the thermistor doesn't fail self diagnostics. Oh well, gambled and lost, new dishwasher time.

Unscrewed brackets on top of dishwasher from underside of counter. Removed dress plate at bottom of dishwasher. Pulled dishwasher out of opening to access door hinge. Disconnected pulley cable/rope from each side door hinge. Let go slowly.
There is a 1/4 bolt holding the door tight to the hinge. With door closed (still) the screw is on bottom of bottom edge. Use wrench to loosen and remove.
Once both bolts are out, open door. Pull door away from dishwasher just enough (1-3 inches) to slide out old gasket. Prior to removing take note of existing gasket orientation and installation. Slide old gasket out one side and slide new gasket in.
Push in door tight to hinges,close door, use wrench to put bolts back in. Reattach pulley cable/rope to each side. Push back into opening. Reattach to counter. Put dress plate on bottom back.
Return dishwasher to regular use.

I fixed this issue by replacing the Dishwasher Tub Gasket (PS11774412) and the gasket on the bottom of the door (PS11700870). Replacing the tub gasket is very easy and straight forward. You just pull it off and put the new one on. The door gasket was much more complicated. See the steps required for replacement below:

The * indicates the part number in the diagram I am referencing

1. Remove the Toe Kick Assembly (*759)
2. Remove screws holding dishwasher to counter and pull the dishwasher out
3. With door shut, disengage the springs on both sides from the arm hinge assemblies *800 (I did this by taking the rope off the pulley hinge *734)
4. Disconnect the wire going from the dishwasher body to the door (there are two or three supports for the wire that need to be removed for it to come free)
5. Open the door about 15 degrees and pull the door upward (only one angle will work for removing the door)
6. Place the door on its front on the ground
7. Remove the two screws (*745) that hold one of the arm hinge assemblies to the door and pull the hinge away from the door (you don't need to pull it all of the way out)
8. Pull the old gasket out to the side and install the new gasket

There was no repair -- it was a simple snap-in replacement of lower spray arm assembly. The shaft holding the lower spray arm in place is plastic so of course it broke when a utensil blocked the arm from spinning.

I appreciate the Parts Select company for enabling me to purchase a replacement part though that allows me to keep my old dishwasher working.

Removed old spray arm. Installed new one. New model spray arm doesn’t need metal heat shields.

damage to gasket (had a slit in the area of the utensii baskets.
causing lower right corner of gasket to come out. caused leakage to floor from the lower right corner of door...

As I am 77 yrs of age I was leary of diy but thanks to the reps of
"Parts Select" I actually was able to put in the new gasket myself.It did take some time and lots of patience as it had to be seated correctly..I also had to make sure the new gasket was in the groove as it is supposed to be.

Thanks to this site for saving me about 150.00.This is my third repair with parts from your company. Thank you.

The dishwasher had been installed before we added 3/4 oak floor, so I could not pull the dishwasher out from under the counter. That will be a major project when the dishwasher dies.
To remove the door, I removed the two 1/4 " screws on the right and left bottom of the door. I used a box wrench since that was the only way to reach them. One had corroded due to a leak. it took some coaxing but finally came loose. The hint about opening the door 27 degrees and propping it open with two Allan wrenches through the hinge holes was very helpful. Then I lifted the door a little and gently pushed toward the counter releasing the door form the hinges. I took the door off to find a leak and found the right corner edge of the inside tub had cracked. Not sure how this happened. I cleaned and sanded the crack area and used J-B Weld to epoxy the crack. Replacing the gasket was easy. Slide out the old, slide in the new. Everything went back together smoothly. If I hadn't needed to repair the tub, the hint about opening the door all the way and sliding it out part way might have worked to change the gasket. Note. Unlike a stove door the dishwasher door is not that heavy.

Online instructions said to remove door. Found no need to. Only need to release one hinge by sliding door upward after removing 2 screws at bottom edge of door which releases both hinges. With door lifted just pry out old seal (it will be stuck so use a strong screwdriver). Then slide new seal in place. Lower door back down on hinge. Job done.

*Unplug the dishwasher. My drain hose was long enough so no need to disconnect.
Access the motherboard and found a solid green light. This indicates the motherboard is not communicating with the user interface.

Door removal:
- removed kick plate
-unplugged door wire assembly and wire harness clip
-Unscrewed dishwasher from cabinet and pull dishwasher out about 6 inches
-Detached pulley rope assembly from door hinge
-Open door about 4 inches and pull up and towards me.
-Lay the door down, removed vent cap and four T20 screws from the side bottom, remove two 1/4 inch bolt from each hinge(the hinges have four bolts, but only to need to be removed)
-push up on the plastic inner door from outer door and set aside.
-Unscrew four 1/4 inch bolts holding user interface and unplug wire assembly. (The two middle screws are longer than the two outer screws)
-be sure to ground yourself before touching the new user interface board
-read the instructions for the new interface board clip positions(mine was already position correctly)
-Assemble the door and be sure to connect the wire assembly and harness clip.

Replaced heating element. This was the path of least resistance but the problem persisted. I tried resetting the dishwasher but still nothing. My last resort is the circuit board. I checked the relays on the old board and they are fine so it must be something else on the circuit board. The dishwasher is not really that old (4 years) and everything else is fine. Just ordered the board so I really hope this fixes the problem.

1) Pull out lower basket plate holder out. Now would be a good time to check roller wheels. 2) Grasp lower spray arm base (knurled collar on base) and turn counter clockwise to release. 3) Install new spray arm and turn knurled collar on base clockwise to lock it in. 4) Reinstall lower basket plate holder.
* Done *

Removed the screen cover and then removed two bolts with nut driver and removed white plastic retaining piece. Pulled flood switch out of housing (raise approximately 2 inches) then unfasten electrical plug. New part connects to electrical plug (pnly can fit one way so no problem with orientation). Pushed floid switch bsck into lace and attached white plastic retainer with two bolts and then set screen cover back. Very simple and easy.