GDF510PSD0SS General Electric Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Daniel from WATERBURY, CT
- Parts Used:
- WD28X22621, WD21X10519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Dish washer wasn't getting the water hot to wash or dry
In did the drain screen, undid two nuts on top, removed panel, undid plastic ring, undid two screws with but driver, pulled sensor up, dried up any water at bottom, installed new sensor and follow steps in reverse. It worked!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from CLIFFSIDE PK, NJ
- Parts Used:
- WD22X33498, WD22X10090
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Kept falling off during use.
Just took old one off & install new one. Snaps on dish rack. Took 5 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Fred from FLORENCE, SC
- Parts Used:
- WD24X10060
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Diswasher was leaking
Drain hose elbow (#326) had a crack in it. Disconnected power, slid dishwasher out and laid on its back. Hose had two pinch clamps to remove. Replace old hose with new one and used standard hose clamps. Put dishwasher back in place and hooked power back up. Entire process took less than 30 minutes. PartSelect had elbow for about $6. GE does not sell just the elbow. They sell whole pump setup for about $106.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from KENNEDALE, TX
- Parts Used:
- WD22X33499
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Loud banging sound when dishwasher was on.
The base of the spray arm literally just spins a little bit into place like a luer lock. Takes two seconds to replace.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephanie from Huntsville, AL
- Parts Used:
- WD12X32798
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers
The soap dispenser was not opening during the washing cycle
Took off the door and separated the two door pieces. Unscrewed the old dispenser and replaced it with the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from SALT LAKE CTY, UT
- Parts Used:
- WD08X21894, WD49X23779
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
The diswaher was not pumping out the dirty water
Once I got the dishwasher out of the cabinet, which required removing the top screws and then the lower face plate. I then removed the old pump by disconnecting the hoses, then removing the old pump by pulling it from the hanger wire. I then disconnected the wire harness. I then put the new pump in place in reverse order. The wire harness connections were different, and the new harness that came with the new pump I was not sure how it may have went with this unit. So I hard wired it by sniping out the wire connector on both sides and wire nutting the connections. Once done I put the dishwasher back in place and tested. Worked like a charm.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from ST AUGUSTINE, FL
- Parts Used:
- WD21X10490
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
washer would nt ru it beeped 3x and flash start lite
Looked upm the problem it said door wasn.t closed so cause was the door latch. put in the new one no change so I bought a new dishwasher
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- GARY from SOAP LAKE, WA
- Parts Used:
- WD12X32798
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
The soap dispenser was broken os to save money I ordered one on-line
The repair instructions were great and the repair went well. The repair took less than an hour.
Thank you
Gary
Thank you
Gary
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from OMAHA, NE
- Parts Used:
- WD28X35779
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Upper rack rusted out
Took out the old and swapped out the parts from the old one and put them on the new rack. Looks great and works great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from DANBURY, CT
- Parts Used:
- WD21X10519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
Ge Dishwasher was not filling with water
I replaced the Flood Switch Part Number: WD21X10519.
I found that be removing the bottom front cover under dishwasher door, there was a small black plastic clamp holding up the wiring cable. By disconnecting the clamp, it gave me a few more inching of wire inside the machine, which made disconnecting old flood switch easier. It also help in installing the new flood switch. Then finally i reinstall the clamp cable under the machine to finish the job.
I found that be removing the bottom front cover under dishwasher door, there was a small black plastic clamp holding up the wiring cable. By disconnecting the clamp, it gave me a few more inching of wire inside the machine, which made disconnecting old flood switch easier. It also help in installing the new flood switch. Then finally i reinstall the clamp cable under the machine to finish the job.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marlene from FT WASHINGTON, MD
- Parts Used:
- WD35X20794
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
new dishwasher with broken upper spray arm
The part did not fit at all but not worth it to me to return it. The part I need is about 20 inches in length and the one sent was about 10 inches. I will simply call for this dishwasher to be repaired or replaced.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from STERLING, CO
- Parts Used:
- WD05X30818
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Dishwasher was not drying
I followed the U tube instructions already put out part select.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- louis from FRANKFORD, DE
- Parts Used:
- WD21X10519
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
dishes were not dry at end of completed wash cycle
Followed the instructions on the video, it was pretty straight forward. It was helpful to know what to expect before hand like removing accumulated water in the drain before removing the flood switch so as not to have that water drain under the dishwasher. Knowing to have a nut driver with magnetic tip was helpful in removing and reinserting the screws. all in all it was pretty easy repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from CARY, NC
- Parts Used:
- WD21X10519
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers
No boost in water temperature; water temperature during wash cycle not hot enough; dishes not drying
Had to trouble shoot to isolated the true fault condition. Checked heating element was good
Researched symptoms on YouTube
Removed and inspected float switch part
Ordered and replaced part.
Researched symptoms on YouTube
Removed and inspected float switch part
Ordered and replaced part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Julian T from Dalton, GA
- Parts Used:
- WD01X35298
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
roller wheel was melted.
I removed the old roller wheels and the new roller wheels snapped together and the simple instructions made the repair quick and simple..
Was this instruction helpful to you?
Thank you for voting!