GDF510PGD1BB General Electric Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Deborah from BRADENTON, FL
- Parts Used:
- WD21X10490
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Door would not shut, machine would not run.
Took out 2 screws that held machine in cabinet. Pulled out dishwasher about 4 inches. removed old latch and disconnected electric connection. Put in new latch, reconnected electric connection, replaced screws, pushed machine back in cabinet, replaced 2 screws that hold machine in place. Works like new!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Josef from MT CARMEL, TN
- Parts Used:
- WD08X21894, WD08X10092
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Leaking under door
Since I have granite countertops, unscrewed 2 screws on each side of cabinet. Unscrewed the toe plate, unplugged the wire connector, and disconnected the cable
from the door which was held by tie wraps. Pulled out dishwasher about a foot. Unhooked the spring cable to the door, lifted the door out and placed it on a spare table. With door face down on a towel, I unscrewed the screws at the bottom to release the latches, then unscrew the screws that hold the door locked in place. Turned the door on its back face up, wedged a flathead driver to release the settings display, from the body of the door. Separated the 2 panels replaced the foam rubber vent seal. Placed the face face down, reconnected both pieces of the door together pushing down. Rescrewed the bottom to lock the 2 pieces together reinsert the hinges, screwed them in with nutdriver1/4". Grabbed the old gasket, replaced it with new one, sliding it into the groove on the bottom inside of door. Reattached the door to the washer, rehooked the cables to the door, retired with zip ties the cable to the underside of door, reinstalled the wire connector, and re screwed the toe plate. Pushed the dishwasher, leveled, rescrewed into cabinet. Replaced the tub gasket.
from the door which was held by tie wraps. Pulled out dishwasher about a foot. Unhooked the spring cable to the door, lifted the door out and placed it on a spare table. With door face down on a towel, I unscrewed the screws at the bottom to release the latches, then unscrew the screws that hold the door locked in place. Turned the door on its back face up, wedged a flathead driver to release the settings display, from the body of the door. Separated the 2 panels replaced the foam rubber vent seal. Placed the face face down, reconnected both pieces of the door together pushing down. Rescrewed the bottom to lock the 2 pieces together reinsert the hinges, screwed them in with nutdriver1/4". Grabbed the old gasket, replaced it with new one, sliding it into the groove on the bottom inside of door. Reattached the door to the washer, rehooked the cables to the door, retired with zip ties the cable to the underside of door, reinstalled the wire connector, and re screwed the toe plate. Pushed the dishwasher, leveled, rescrewed into cabinet. Replaced the tub gasket.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from CASEVILLE, MI
- Parts Used:
- WD21X10490
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Dishwasher would not sense door was latched
Super easy repair, just removed the old latch and replaced it with the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gregory from EXPORT, PA
- Parts Used:
- WD08X21894
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
Old corroded gasket
Replaced gasket with a new one before further problems occurred. Got to get it in but it was relatively easy to place and snap in just make sure it fits on the right place where gasket inside meets ridges on door so it will be on properly for proper fit.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donald from NASHVILLE, TN
- Parts Used:
- WD21X10490
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Dishwasher door sensor/ mother board
Replaced motherboard, parts select,very helpful in helping diagnose problem! Exchanged parts, credit account after returned parts. Great customer service All good stuff! They brought their A game for this diy-er...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from CLIFFSIDE PK, NJ
- Parts Used:
- WD22X33498, WD22X10094
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Kept falling off during use.
Just took old one off & install new one. Snaps on dish rack. Took 5 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nicholas from CONCORD, NH
- Parts Used:
- WD05X30818
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Wrench (Adjustable)
Dishwasher was not heating up to dry
Took out the old heating assembly and installed the new one
this did not solve my problem and I ended up buying a new dishwasher and returned the part
Spent as much in shipping to get the part and return it as the part cost itself
Next time I will just replace the dishwasher in the first place.
this did not solve my problem and I ended up buying a new dishwasher and returned the part
Spent as much in shipping to get the part and return it as the part cost itself
Next time I will just replace the dishwasher in the first place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Melissa from BELLPORT, NY
- Parts Used:
- WD22X10094
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Connector to sprayer broke
Connected sprayer aligned on bottom of top rack snapped in place. Very easy to install!
Was this instruction helpful to you?
Thank you for voting!