CDWT280V50SS General Electric Dishwasher - Instructions

Simply took out the broken rack and inserted the new one.

Twisted new one in place of old. Disappointed that there was a melting issue at all. Need to investigate problem.

Just pulled out the old basket and put in the new one. . Don't know the holes got into the basket. . .

Had purchased SPRING DOOR, CABLE ASM, and HINGE CABLE PULLEY prior to starting repair, as I did not know which piece had failed. Cable assembly was the culprit. SPRING is heavy duty steel, HINGE CABLE PULLEY is nylon, and CABLE ASM (assembly) is braided steel with a steel plate at one end that ties into spring and an inadequate nylon piece that ties into the steel hook on the door. The nylon piece failed through tearing open. REPAIR STEPS: 1. Removed bottom cover plate at front. Two hex head nuts. Nut driver works best but Phillips head screw slots are on nuts. 2. Removed dime-sized cover plates located on either side of main unit where door seals when it is closed. Used Phillips head screwdriver to remove screws that are screwed into cabinets flanking dishwasher. Magnetic tip will help keep you from losing these between dishwasher and cabinet as they are too short to project through the access hole when fully unscrewed. 3. Lowered appliance feet using adjustable pliers. Slip wrench would probably work but six-sided appliance feet are slippery. 4. Loosened drain hose clamp from disposal and removed drain hose. 5. Shut off water line to dishwasher (under sink) and disconnected water line with slip wrench. Steps 4 and 5 were done to give me the slack I needed to pull dishwasher out from cavity far enough to access the side where the repairs were to be made. You may or may not need to do that--try pulling dishwasher out first and see how far it will go. 6. Looked at the problem, which was failed cable assembly. 7. Removed nylon Hinge Cable Pullley with nut driver. This allows cable removal. 8. Put cable back into place (loose) and then replaced Hinge Cable Pulley. 9. Reattached cable to spring on back end and door hook on front end. 10. Pushed dishwasher back into position. 11. Raised appliance feet to proper height. 12. Reinstalled side screws that hold dishwasher against cabinetry. 13. Replaced small screw cover plates. 14. Reattached drain line to disposal. 15. Reattached water line. 16. Turned water on and checked for leaks. 17. Reattached bottom cover plate to front of dishwasher.

Found numerous references on internet that most likely cause was due to a fouled or plugged suction screen. I unscrewed anchor tabs on top securing the dishwasher to the countertop, slightly lowered the front screw legs, turned off circuit breaker at the electrical panel, checked to verify the power was off, removed the small electrical cover under the dishwasher and disconnected the 3 wire nuts, pulled the dishwasher partially out, then disconnected the small corrugated drain hose from the discharge pump under the washer being careful to collect small amount of drain water in a bowl. Finally, carefully pulled dishwasher out from under the countertop leaving the hot water supply hose connected. Tipped washer over onto back (the frame rails are rounded in the back to help facilitate this). Had to unscrew the hose clamps to remove the rubber sump. Then stood the dishwasher back up to disassemble the plastic screen parts from inside the dishwasher. The screen was in fact plugged with white slimy deposits that when dried became chalk like. During cleaning out the white caked on deposits in the rubber sump, I accidentally pushed my screwdriver through a rubber vent stand tube and this is why I had to buy a new rubber sump. The sump rubber material appeared to be partially deteriorated which is why my screwdriver passed through it. Reassembly wasn't very easy. It was difficult to get the rubber sump boot over the plastic flange on the bottom of the tub. It helped to remove the metal hose clamp completely and to have someone hold the dishwasher in place lying on its back while I pushed and prodded to get the rubber seal over the oval flange. Once on, everything went back together easily in reverse order. It probably took me a total of 6 to 8 hours of real working time. But taking into account that I only worked for short periods of time on evenings after work and the fact I had to lug around my extra 70 lbs of gut, the constant laying down and getting back up, the 4 day wait for the new rubber sump to arrive, and my near senior citizen age stretched this 8 hours of work out to a two week home repair project. BUT, I was successful and everything is back to perfect working order. Thank you Partselect.com for having the sump in stock and to my door in only 4 days!

Replaced wax motor and soap dispenser (all one piece). Only problem was the plastic seal on the very bottom of door had come unseated, and therefore was leaking. You need to check that it is snapped all the way in, and then the leak ceased. Took me a few tries, which made a ten minute repair into an hour long one.

This is a somewhat difficult task in that the dishwasher had to be pulled out of the cabinet which required the water inlet hose to be removed (and water to the hose to be shut off). Once the dishwasher was free of the cabinet it had to be flipped over to reach the water inlet valve. Once the valve was replaced go in reverse to reinstall the dishwasher. Worked fine after I got everything installed; no leaks.

removed front panel and replaced new part. Timer did not work because plug kept disconnecting. Called GE service and watched him remove panel without removing control panel. Plug for timer can be installed easily and front panel replaced without disturbing cable.

Water was leaking from under refer next to installed under counter dishwasher. Once determined to be dishwasher not refer I removed dishwasher toe place was able to see dripping inlet solenoid valve. I had to disconnect 11V power, shut off inlet water, disconnect inlet water house and remove dishwasher from under counter. Once dishwasher was in center of kitchen I flipped it upside down and removed the electric solenoid inlet valve. Removing the valve took one wrench to remove inlet hose then two wrenches to remove 90 degree brass fitting and another to hold solenoid. I used a nut drive to remove two screws that released the solenoid from the dishwasher frame. I used teflon tape to reattached the 90 degree brass fitting and inlet hose.

Shut off water, disconnect drain line from disposer. Remove dishwasher from wall and remove water feed line. Unplug or disconnect power to unit. Remove upper and lower dish racks as well as lower water sprayer bar, and filters. Lay dishwasher down on backside (make sure to catch water with bowl). Disconnect pump connector with nut driver and replace. Stand dishwasher back up and reverse removal process

I had a small leak from under the dishwasher which turned out to be a tiny hole in the Pump Connector. With the power off I pulled the dishwasher out of the cabinet and disconnected the water and drain lines to give me more room. I put the dishwasher on its back to have access to the pump assembly. A couple of nut drivers and the pump connector is accessible. Replaced the pump connector and over tightened it "Crack"... had to replace the Main Conduit connector ($50). I was able to turn a simple $20 repair into a $70 repair. Now that's talent!

Replaced the part by taking off the srews on the inside of the dishwasher door (all of them)to get to the backside of the soap dispenser. Remove an electrical connector by pulling (had to pull off using pliers as it was really on there). Then a couple of screws hold to to the inside of the door. Pretty straight forward.

The quiet power 3 has the heating element in the back, so remove the screws holding the unit in place. Remove the bottom cover and disconnect the water inlet pipe, (after turning off the water of course). Discard the copper tubing if applicable, and pull dishwasher out until you can tilt it forward. Unsrew the plastic nuts and remove the wires for the element. Test the old one to make sure that you need to replace it. When sure of the problem reinstall in the reverse order. Replace the copper with stainless steel braided line and test.

very happy with the product and fast shipping. removed kick plate from dishwasher, inlet valve was on the front left bottom slid out dishwasher removed two screws and disconnected water line,and installed new inlet valve,very simple job if your somewhat handy,make sure you use thred sealant on water line when re installing

The tub gasket is very easy to replace. First I pulled out the old gasket then using the center marking on the new gasket, I centered the gasket at the top then pushed the gasket into the track. At the bottom I reused the wire that holds the two ends in place making sure I attached the separation wire in the same configuration as with the old one. I had another leaking problem with the seal on the bottom of the door. GE does not sell a repair seal for the door bottom and a new inner door must be purchased at around $200. I made that repair using an old bicycle inner tube. I cut the tube into a one inch strip and epoxyed the strip to the tub where the door meets the tub.. Worked perfectly!