ADW1100N35BB General Electric Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Ralph from McMinnville, OR
- Parts Used:
- WD12X10284
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Damaged rinse agent dispenser
Unscrewed old one and installed the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from JONESBOROUGH, TN
- Parts Used:
- WD15X10014
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Wrench (Adjustable)
Would not fill with water
Ordered most likely part...water inlet valve.
1. Turn off water supply.
2. Remove the metal toe kick plate/insulation at the bottom of the
dishwasher.
3. Remove hose to supply valve.
4. Take electrical plug off old valve.
5. Remove float valve because it was mounted it right in the way of
the 2 screws on the inlet valve bracket.
6. Remove those 2 screws now you can get to them, and move the
inlet valve to one side so you can get to the hose clamp for the
rubber hose out of the valve going to the dishwasher.
7, Take the old valve and bracket out, mount new valve on the
bracket, crawl back down on the floor, reinstall rubber hose and
bracket, and float valve and finally inlet hose.
8. Turn water on. Check hose connections for leaks. Yep, outlet
hose didn't clamp enough now, allowing a drip.
9. Repeat the whole process AGAIN. Replace little clamp
with a REAL hose clamp, reinstall the thing again. No leak this
time.
10. Test run dishwasher thru a cycle. Check again for leaks at hose
connections. OK ? Reinstall insulation pieces and toe kick
plate.
1. Turn off water supply.
2. Remove the metal toe kick plate/insulation at the bottom of the
dishwasher.
3. Remove hose to supply valve.
4. Take electrical plug off old valve.
5. Remove float valve because it was mounted it right in the way of
the 2 screws on the inlet valve bracket.
6. Remove those 2 screws now you can get to them, and move the
inlet valve to one side so you can get to the hose clamp for the
rubber hose out of the valve going to the dishwasher.
7, Take the old valve and bracket out, mount new valve on the
bracket, crawl back down on the floor, reinstall rubber hose and
bracket, and float valve and finally inlet hose.
8. Turn water on. Check hose connections for leaks. Yep, outlet
hose didn't clamp enough now, allowing a drip.
9. Repeat the whole process AGAIN. Replace little clamp
with a REAL hose clamp, reinstall the thing again. No leak this
time.
10. Test run dishwasher thru a cycle. Check again for leaks at hose
connections. OK ? Reinstall insulation pieces and toe kick
plate.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rhonda from CANTON, GA
- Parts Used:
- WD13X10003
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Latch was broken so dishwasher wouldn't run
I watched several YouTube videos on how to make the repair. It looked very easy but sometimes professionals, because they've done it before, don't point out small tips that would help a DIY homeowner. The latch goes easily into the inner door slot but there's nothing to hold it there. The videos show the inner and outer door being closed together without showing that you have to hold the latch in place while bringing the outer door up to meet the inner door. Any movement of the inner door makes the latch fall out. So I would say it took me 5 times longer to do this repair than it would if I was doing it again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from Blairs, VA
- Parts Used:
- WD12X10304
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken off end caps, top would slide off, frustrating.
did it by hand, carefully flair out the plastic piece only enough to slide it into the metal rail.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Millerton, NY
- Parts Used:
- WD08X10057
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
Leaking door
My husband said it was easy. But the gasket didn't solve the problem. So we had to order another part. We had to order the little black stoppers that go in the hinge area. Still leaked so my husband took them back out and cleaned the area. Then put some kind of sealant in and replaced the black robber things. So far that worked.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- edward from noblesville, IN
- Parts Used:
- WD28X31819
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
lower rack was rusty
Took out the old one and put in the new one! Note the delivery time was great! The part was ordered one day and delivered the next! Thank You Ed Andrews
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Allan from Williston, VT
- Parts Used:
- WD12X10304, WD28X31820
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
2 wheels on original track rusted/broke through
Removing the slide end caps was a little tricky. Key was to tilt and twist the end cap and slide out. Putting them back in was equally as tricky, but reversing the process helped. Sliding the new track in place was simple. Total repair took about 6 or 7 minutes.. Part was ordered on a Monday morning and delivered the following day using standard shipping. Outstanding service.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jose from Anthem, AZ
- Parts Used:
- WD28X31819
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
new bottom dishwasher rack
it was super easy and the part came in days. it was super quick
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from ANNAPOLIS, MD
- Parts Used:
- WD15X10014
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
Leaking Solenoid valve
1.Shut off the electric! 2.Shut off the water Supply. 3.Removed the two lower front panels(Two bolts each) . 4.The Water supply Solenoid is located far left up front . 5. Unplug power connector clip to the solenoid. 6.remove the two mounting bolts . 7. Use pliers to compress the rubber hose clamp And slide down the hose . 8 some small amount of water maybe in the hose a pan maybe necessary under the solenoid. 9.Gently pull the rubber hose off the nozzle. Complete installation in reverse. May The Force Be With You!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward from GRAND BLANC, MI
- Parts Used:
- WD35X21038
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
NONE
UNPACKED WHEELS AND CLIP. USING NEEDLE NOSE PLIERS SQUEEZED WHEEL TIP TO INSERT IN WHEEL. REMOVED OLD WHEELS AND RETAINER BY HAND. INSTALLED NEW WHEELS INSTALLED AND NEW RETAINERS
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- karen from Corona, CA
- Parts Used:
- WD28X31820, WD28X31819
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
dishwasher rack corrosive
Very simple. First recieved Top rack. used a flat head screw
driver to remove cone/tower, put cone on new rack. put rack
on grove slided in easily. Took old rack out.replaced with new easily
driver to remove cone/tower, put cone on new rack. put rack
on grove slided in easily. Took old rack out.replaced with new easily
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- helmut from EAST KINGSTON, NH
- Parts Used:
- WD35X21038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Lower wheels kept falling off
Installed new lower rack wheel kit
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frank from WEST DEPTFORD, NJ
- Parts Used:
- WD08X10057
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Door gasket was old and leaking.
I watched the video instructions and it looked easy! The old gasket just pulled right off easily! Installation of the new gaskets was quick and easy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kenny from CARUTHERSVLLE, MO
- Parts Used:
- WD13X10003
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Dishwasher would go on and off during operation
Took screws out of door panel to get to the latch and replaced old latch with new one. Super easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Harry from CLEVELAND, OH
- Parts Used:
- WD08X10057
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Leaked at bottom of door
I took the inside of door off to install both gasket and gasket insert. Much easier this way. Also it’s much easier to fish locking handle through the door if you extend the handle half way and put through opening when raising the door.
Was this instruction helpful to you?
Thank you for voting!