ZBD7920P30SS General Electric Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- DONALD from PORTLAND, ME
- Parts Used:
- WD35X21041
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The lower dishrack connectors on the original roller axle parts had loosened so the rollers kept falling off
1. assemble each of the new rollers and axles by inserting the axle through the roller from the back side; push until the two parts snap together; 2. remove the cutlery basket, take the lower dishrack out of the dishwasher and turn it upside down; 3. remove the old rollers from the dishrack and send them for recycling; 4. push each roller on the corresponding wire shaft of the dishrack, with the axle connector arm against the vertical part of the shaft, pushing the roller assembly against the shaft until it snaps together. NOTE: the new rollers are wider than the originals and fit snugly on the tracks; no wobbling; the connector snaps are an improved design that should last as long as the dishwasher.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carri from Louisville, KY
- Parts Used:
- WD12X10163
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
latch on detergent assembly broken off
Easy repair-removed hex nuts and and screws to pop out old part and replace with new one. New part works better than the original! 1st replacement part arrived with a broken piece, a quick, courteous phone call got a replacement sent out. It took a 2nd phone call to obtain the refund, but the customer care reps are efficient and friendly. I would order from them again for positive service reasons alone.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Laura from Roanoke, VA
- Parts Used:
- WD35X21041, WD35X21038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
missing wheel on bottom rack of dishwasher
Just snapped the stud roller through the center of the wheel and then attatched it to rack.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- GEORGE from LEVITTOWN, PA
- Parts Used:
- WD15X10014
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
Water leak under Unit
Remove Base Access Panel; Removed Valve Mounting Bracket & Valve; Disconnected Wire Connector; Disconnected Supply Line & distribution Hose; Reversed the Process. Piece of Cake; Part was O.E.M.Component Exact Fit; Took Longer to Write this than it took for Fix. Thanks I Will Be Back for other Parts.!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from Denvr, CO
- Parts Used:
- WD12X10122
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Dispenser Cap Missing
Ordered new cap and put it on when it arrived.
Simple
Simple
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marvin from Lake Worth, FL
- Parts Used:
- WD35X21041, WD35X21038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Bottom tray not moving properly
Install the rollers on the studs first, then snap the assembly onto the tray. Really easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jerome from Arlington, VA
- Parts Used:
- WD12X10122
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Lost Rinse Aid cap
Inserted new cap purchased from PartSelect.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Darrell from WAHPETON, ND
- Parts Used:
- WD35X21041
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Bottom dish rack would not roll in and out because several wheels were off because of broken axles. It had to be lifted to get in and out which resulted in many chipped and broken dishes.
I removed the bottom rack from dishwasher. Took off the wheels with the broken axles. Put the new axles on the new wheels and slipped them on the rack. They fit perfectly and rack now glides in and out smoothly. Easy as pie, and took less than 10 minutes. Parts arrived in just two days. Thanks for the great service.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barry from FISHKILL, NY
- Parts Used:
- WD35X21041
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
one old roller broke
pulled off all old rollers and axiies and snapped on new ones
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jimmy G from SPRING, TX
- Parts Used:
- WD15X10014
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
Water leakage at valve
I watched the video that came with email on part. Gave instructions on how to. Thank you !
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alice from BLAINE, MN
- Parts Used:
- WD12X10122
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
cap had melted mi
Unscrew the old one and screw in the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sharon from THE VILLAGES, FL
- Parts Used:
- WD35X21038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The wheels on the lower rack of our dishwasher kept falling off.
Removed the lower rack. Took off the old wheels. Put the axles on the new wheels which took a little manpower, but became easier once you did a couple (there are 8 wheels). Then snapped the new wheels on the rack which was really simple. The new design is much improved to the old one. The wheels glide better, then they ever did. We're sorry we didn't think of this repair years ago and the cost was a fraction of the cost of a new dishwasher.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Harinder from CHESTERFIELD, NJ
- Parts Used:
- WD12X10163
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
detergent dispenser was not closing and dishes were dirty
followed the video step by step which was very well expalined and was able to complete the install
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jesse from Moberly, MO
- Parts Used:
- WD35X21041, WD35X21038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Rollers constantly fell off of lower rack
I pulled off the old rollers and studs and pushed out the old studs and replaced with the new ones. Then I popped the new studs and rollers back on. Job completed and it has been wonderful. The new studs are much more industrial like than the ones that came on it. What a relief.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Melissa from WARNER ROBINS, GA
- Parts Used:
- WD35X21041
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Dishwasher not cleaning properly
The kit came with the anchors and the riollers for the bottom shelf. They clipped right on! Dishwasher cleans great now!
Was this instruction helpful to you?
Thank you for voting!