PDWT500P00WW General Electric Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- John C from SPRINGFIELD, VA
- Parts Used:
- WD28X25960
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Bottom dishwasher rack rusted out
Simple install- just roll it in. Fit perfect. Better design than OEM part. Perfect.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michelle from Carlisle, PA
- Parts Used:
- WD12X10163
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Detergent cap would not stay closed
After removing the screws, the front of the dishwasher easily came off. I put 2 screws back in to hold the control panel in place. I did not want that to dangle while replacing the part. The part came off easily after removing the screws. Everything went together easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jim from Palatka, FL
- Parts Used:
- WD28X25960
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Old rack was rusted out and missing most of the wheels.
Easiest repair ever. My new rack arrived in three days, opened the box and slid it in. Better quality than the original. Excellent service!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from Oakland, NJ
- Parts Used:
- WD35X21036
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
worn wheels on upper rack
parts were easy to find and the repair was a breeze. Thanks for your help.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- sean from oakland gardenns, NY
- Parts Used:
- WD35X21041
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
clips on wheeles were broken
replaced clips that were much better made.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- KEVIN from MACKINAW, IL
- Parts Used:
- WD12X10163
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The detergent dispenser latch was broken
The repair was easy. Removed all the screws from the inside door panel, approx. 11. Watch out for that last screw as there isn't anything else holding the outside panel, inside panel and control panel together other than those screws. I then unplugged the old dispenser backed out another 6 screws and replaced the old dispenser with the new one. Put it all back together within about a half hour.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eric from SIMPSONVILLE, SC
- Parts Used:
- WD12X10163
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
The door on dishwasher soap dispenser broke.
Repaired the soap dispenser.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ron from TYNGSBORO, MA
- Parts Used:
- WD08X10032
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Started to have a leak
Pull out the old, died gasket. Clean out track that holds gasket. insert new gasket.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marc from Brambleton, VA
- Parts Used:
- WD28X24469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Replace the middle flatware basket
So easy, even I was able to do it. Slide tabs back on defective basket and remove both sides, then slide the tabs onto new basket and place in dishwasher. All Done!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kenneth from Dublin, OH
- Parts Used:
- WD12X10163
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Old soap dispensor latch would not hold
Turned off the power at the main box. Removed the six phillips screws and two bottom hex screws holding the front panel. Removed the two solenoid wires on the old dispenser (Label wire polarity). Removed the eight screws holding the old soap dispensor and took it out. Cleaned the area around the hole. Laid down a bead of silicon caulk around the hole edges. Placed the new dispenser in the hole and replaced the eight screws (do not over tighten). Replaced the two wires on the dispenser solenoid (check polarity). Replaced the front cover (Do not over tighten. Turned on the power and job complete.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JOHN D. from GOSHEN, IN
- Parts Used:
- WD01X10175
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
wouldn't drain
Removed the dishwasher to get at the defective parts and removed,than replaced the two check valves and reassemble.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ARTHUR from OAK PARK, IL
- Parts Used:
- WD12X10163
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Pliers, Screw drivers
Detergent dispenser did not work
Followed the instruction video on your website. It was accurate and valid. The repair should have taken 15 mins., instead one of the screws holding the dispenser was frozen. Tried DW-40, and liquid wrench. Neither worked because the screw was in plastic.Finally got out the Dremel and cutting wheels. Had to cut away enough of the unit until I could get at the screw (it was the center bottom one). Sliced through some more of the housing, then cut a notch in the screw head deep enough so I could apply enough pressure with a flat blade screwdriver to open it. After that things went as smoothly as could be expected.A bad design and cheap materials.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- SUSAN from LAKE FOREST, CA
- Parts Used:
- WD35X21041, WD35X21041
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Wheels became loose
Really all it took was removal of the old wheels which would not stay on anyway and the installation of the new ones. That required the axle and wheel being put together and the installing both of those on the lower rack. I was about to buy a new dishwasher when the salesmen told me about a product called Lemi Shine it saved my hundreds of dollars and the inside of my dishwasher looks brand new. With my new wheels I am good to go again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from TAMPA, FL
- Parts Used:
- WD35X21041
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Old rollers broken
No instructions. At first thought I needed instructions. A minute later I was attaching the new rollers. Simple and easy. Took less than 15 minutes. Would recommend these rollers.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Norwell, MA
- Parts Used:
- WD24X10045, WD01X10279
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers, Wrench (Adjustable)
New install missing drain tube and clamp.
Purchased new $1400 dishwasher from sales floor for $699. Cosmetically perfect, but missing drain tube and clamp. Seemed like a good deal... and it was. Needed parts were $34. Install of this machine was a breeze, and it is suoer quiet...I need to get down on the floor and listen for water flow to know that it's working. Really.
Was this instruction helpful to you?
Thank you for voting!