Models > PDWF680R10SS > Instructions

PDWF680R10SS General Electric Dishwasher - Instructions

Jump to:

All Instructions for the PDWF680R10SS
121 - 135 of 213
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Edward from Granite Bay, CA
Parts Used:
WD08X10032
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
tear in the tub gasket
Pulled out the old gasket and replaced with the new gasket. Inserted the steel spring clip into the ends of the gasket. Repair complete.
Was this instruction helpful to you?
Thank you for voting!
Customer:
William from Henrico, VA
Parts Used:
WD13X10045
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
The latch on our dishwasher broke
I unscrewed all the screws from the inside of the dishwaher door. I took out the broken part, installed the new parts and screwed the screws back in. Part Select was wonderful to work with and the parts arrived the day after they were ordered.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Frances from Goodyear, AZ
Parts Used:
WD08X10032
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Our tub gasket was torn by leaning utensils (a definite design flaw.)
Just have a good look at how the original is installed before removing, then clean the area. The new one was a breeze to install, just line it up and pop it in.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Pierangela from River Forest, IL
Parts Used:
WD12X10163
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
the soap dispenser door had broken off
Open the door and go along entire edge of door and use Philipps to unscrew the front panel of the door from the inside panel of the door. Once unscrewed open carefully. There are screws in the dispenser cup. Undo those and then there are two plugs to be undone. There is also the main black computer component that has to be unplugged from its cord. Just remove and screw everything back the way it was. This was my first time and I am a female age 58 years old. It was simple. If I had to do it again I could do it in less than half the time.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Cerem from Staten Island, NY
Parts Used:
WD13X10045
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
There was no problem in installing this part
Easily screwed on this part and used it for the door of the dishwasher to properly open and close
Was this instruction helpful to you?
Thank you for voting!
Customer:
mike from toms river, NJ
Parts Used:
WD21X10169
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
dishwasher would not run
Prior to starting, make sure power is off at unit by turning off breaker. Opened dishwasher and removed screws from back of door panel exposing switch. Remove screws holding switch in place. Removed electrical connections from switch and installed in reverse order of removal on new switch. Re-attached door panel and ran dishwasher cycle.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Jane from Phoenix, AZ
Parts Used:
WD08X10032
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Rubber door gasket pulled away from dishwasher when door was opened after a wash or when sliding the top rack out
Removed the door gasket and cleaned the track prior to installing the new gasket. The online repair instructions didn't mention a thin wire that is stored at the bottom of the tub near the door and is used to hold the ends of the gasket in place. Gently remove the ends of the gasket from the wire prior to pulling the entire gasket out of the machine track.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Donald from The Villages, FL
Parts Used:
WD26X10053
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver
Leak from motor output/pump input shaft
Cut power and water flow to the appliance. Laid appliance on its side, removed the electrical lead from the motor. Remove the mount from the back of the motor and loosened the two clamps- one to the sump and one to the discharge tube. Removed and replaced the pump/motor assy. with the new one, reinstalled the clamps, rear mount and electrical lead. Righted the unit and fired it up. Worked fine.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Donna from Apollo, PA
Parts Used:
WD12X10163
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
dirty dishes wash after wash
We noticed our detergent door was not opening on cue to dispense the soap and it was leaving our dishes dirty. It came to be that our spring was sprung on the detergent door. I researched it and I could either buy the spring or the whole detergent contraption (installing the contraption was one wrench easier but cost $35 more). Knowing my husband the way I do, I decided to do the more costly route. I followed the instructions from previous installers on here and me and my husband did it in 30 minutes! I do agree that it is a two man job for some of it as I stressed to him NOT to take the front off haphazardly, as it was $400 to replace that! We took the 12 or so screws off, detached the line to the detergent dispenser, reattached, screwed it into the door and replaced the front 12 or so screws again. Easy peasy! Unbelieveable!
Was this instruction helpful to you?
Thank you for voting!
Customer:
Victoria from Shepherdstown, WV
Parts Used:
WD08X10032
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Water leakage
I examined how the old gasket was attached before removing it. I then pushed in the new gasket needing no tools. There has been no water leakage since.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Sara from Greenwood, IN
Parts Used:
WD12X10163
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
The detergetn dispenser door hinge was broken.
I unscrewed the screws in the door of the dishwasher. Then pulled the inside part of the door up and unscrewed the 6 screws that held the dispenser. I am not sure the correct name of the part but it is on the backside of the dispenser and is red and it is where the wires connect to it, that was probably the most difficult part, disconnecting the plastic covers from the old dispenser. I used a butter knife to pop it out and then was able to get a better grip to pull them off. I pushed the wires on the new red thing and then put the new dispenser in place. You have to make sure that the dispenser is in the right spot and the brace on the underside of the inside part of the door, is in the correct place, otherwise, you will have a leak. Which is what happened to me. I just unscrewed and opened it again and screwed the screws tighter and it was fine.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Mike from Rockwall, TX
Parts Used:
WD03X10022
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Socket set
Appeared to be spring on dishwasher door.
Removed two pieces on bottom, pulled dishwasher out changed a cable and put it all back together! It was a little plastic piece that broke! Thank you for you quick response! Ordered one day came two days later! Great service!
Was this instruction helpful to you?
Thank you for voting!
Customer:
Lisa from Missouri City, TX
Parts Used:
WD28X10410, WD28X25960
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
both top & bottom racks had rusted (7 yrs old)
bottom installation was extremely easy. top installation required removing the spin piece and reattaching it to the new basket so it was a little more challenging but having the new racks is wonderful! Very quick delivery which was great.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Barbara from Angleton, TX
Parts Used:
WD12X10384
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
liquid soap dispenser failed to work
removed inside door panel to access the pump; then replaced with new pump
Was this instruction helpful to you?
Thank you for voting!
Customer:
Chris from Carleton, MI
Parts Used:
WD15X10014, WD21X10355
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Wrench (Adjustable), Wrench set
The Water inlet valve was leaking.
I disconnected the pipes to the inlet valve. I removed the bolts from the bracket holding the valve. I tried to use two wrenches to remove the brass angle pipe thingie off the bottom of the old valve. I then beat on it with a hammer, then I just threw it against the basement floor till it came off. I would recommend getting a new brass angle pipe thingie before you start.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the PDWF680R10SS
121 - 135 of 213