PDWF600R10BB General Electric Dishwasher - Instructions

I took out the old rack and rolled in the new. I thought I was going to have to take the rollers off the old one and put them on the new, but they were already on the new rack. The hardest part was getting into the box. I am an 80 year old female.

It was an install. My problem is that the drain tube is not standard to other dishwashers,so I could not get it at either of the local home improvement centers. The good news is that it is larger than the standard, and offers better discharge.

Simple as 1,2,3.Parts on time and priced right.

First I removed the 8 screws on the interior side of the door that holds the plastic inner-face to the door assembly. This allowed me to easily pry the inner face away from the outer face which exposed the latch assembly.

The broken latch practically fell out making it very easy to work the new one into place.

I replaced the 8 screws, closed the door until I heard it latch and then squeezed the handle and was rewarded with a very satisfying sound and feel as the door popped open without a hitch.

I know a repairman would have cost me a minimum of $75 plus a hefty price for the part.

We had to replace the soap dispenser. My husband is not very handy & this was a snap. You take off the front panel (cover) of the sishwasher & simply unscrew the old one & screw in the new one. I probably could have done it myself.

I received the rollers but not the stud rollers in my first shipment. I telephoned and explained that I also needed the stud rollers, which are the axles for the wheels. The stud rollers were FedExed immediately with the shipping waived.

I popped the wheels onto the stud rollers and then popped the assembled roller and stud onto the basket. You can not make a mistake if you put the roller(wheel) on the stud roller(axle) before putting it on the basket. There is then only one way it will pop onto the basket. These are much better stud rollers than the original eqipment ones. They grip tight and don't slip off.

Very easy! Removed 4 screws that was holding the valve to the bracket. Placed bracket over water inlet line. Attached copper threaded coupling with pliers.Screwed valved on to the coupling. Attached bracket to the valve with 4 screws. Reattached water line. Attached bracket to frame of dishwaser. Put kickplate back on and done!

I removed six screws and unplugged the module and removed.
Replaced by the new module and plugged in and then replaced the six screws.
Very easy to fix.

First, remove the bottom front covers (two parts four screws). Second, remove the two screws at the top that secure the dishwasher to the counter. Third, gently pull away the dishwasher from underneath the counter just far enough to see and be able to remove the door spring(s) - one on each side. Fourth, remove the existing hinge arm link(s) if not already broken off, replace with the new one(s). Note that the door hinge goes on the door (front) side of the spring and the other side fits into a groove on the door arm - the other end of the spring attaches to one of the 3 available holes on the frame at the bottom. It would be a good idea to replace the hinge arm links on both sides even if only one is broken. Make sure that the door has the right tension (each spring can be hooked in 1 of 3 holes to adjust the tension). Then gently push the dishwasher back under the counter. Finally, replace the screws under the counter and replace the covers on the bottom front. All of this should take no more than 15-20 minutes. This was an easy job!

Parts were easy to find, easy to order and arrived prior to the advertised delivery date. Instructions for replacement were easy to understand and in about 10 minutes the old part was removed, and the new one installed. thanks for your prompt and efficient company.

hubby had no prob replacing the new part!!YEA!!dishes are clean again!

Took it apart found the problem,went on line orderd the part which came right away. Had it back together in 10 minutes

Remove top rack stops, slide out upper rack from rack railing, turn over upper rack and attach spray arm using spray arm bearing and screw. Reassemble in reverse order.

Removed screws that held dishwasher under cabinet...pulled out DW...removed old part...replaced with new....easier than falling off a stump.

I handed the parts to my husband and asked him to do it.