PDWT580R30SS General Electric Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Pierangela from River Forest, IL
- Parts Used:
- WD12X10163
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
the soap dispenser door had broken off
Open the door and go along entire edge of door and use Philipps to unscrew the front panel of the door from the inside panel of the door. Once unscrewed open carefully. There are screws in the dispenser cup. Undo those and then there are two plugs to be undone. There is also the main black computer component that has to be unplugged from its cord. Just remove and screw everything back the way it was. This was my first time and I am a female age 58 years old. It was simple. If I had to do it again I could do it in less than half the time.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Ocala, FL
- Parts Used:
- WD12X10163
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Detergent dispenser would not latch
Repairs do not get any easier than this. Remove 12 screws to disassemble door panel (be careful not to let front panel of assembly to drop or bend when screws release it). Remove 6 screws to remove old detergent dispenser. Unplug cable from old dispenser. Connect cable to new dispenser. Install new dispenser into door with 6 screws and then reassemble door panel with 12 screws making sure to keep all wiring free from pressure points.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Peter from Davenport, FL
- Parts Used:
- WD14X10009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Hing arm broke
Removed dish washer from cabinet area and snapped new clip into cable and hook into support.. The time that took the longest was to removed the screws to pull the unit out of the cabinet area.. Very easy fix...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carol from Pepperell, MA
- Parts Used:
- WD28X25960
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Bottom Rack Was Rusted Out And Wheels Broken
Installed new rack assembly and it works fine. Thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Martha from Kingman, AZ
- Parts Used:
- WD12X10122
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Rinse Dispenser Cap melted on heating coil
Opened dishwasher after it completed a wash cycle. Found the rinse dispenser cap had come off during the wash and melted on the heating coil at the bottom of the machine. Pulled cap off of coil, made sure coil was not disturbed. Looked in various sites for cap. Finally found this site where I didn't need to order the whole mechanism and could order just the cap. Received the cap, screwed into the dispenser, fixed. The only problem I had was that there were two possible caps so I picked the one that was the same color as the original one. Project completed. Thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward from Arlington, VA
- Parts Used:
- WD28X25960
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Roller rusted off lower rack
removed original rack, inserted replacement.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Victor from East Northport, NY
- Parts Used:
- WD28X25960
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Replaced lower rack assembly
Simply took out the broken rack and inserted the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Calvin from Mankato, MN
- Parts Used:
- WD12X10122
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
aid cap melted
Twisted new one in place of old. Disappointed that there was a melting issue at all. Need to investigate problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nancy from Garner, NC
- Parts Used:
- WD28X24469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Grate in bottom of the basket broken
Removed old basket, put in recycle bin, placed new basket in dish washer. The damage to the original basket was my fault. I now know not to drop heavy knives point down into the basket.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- kathy from zionsville, IN
- Parts Used:
- WD28X25960
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Lower Carriage Wheels So Bent It Would Not Move.
Took old one out, put new one in in less than 20 seconds!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jerry from Calistoga, CA
- Parts Used:
- WD12X10163
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Dirty Dishes, Dispenser Stopped Working
Ordered part online, arrived two days later. Removed and replaced dispenser with new unit. Easy job. Dishwasher works like new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jack from Indio, CA
- Parts Used:
- WD28X24469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
removed old silverware basket
installed new silverware basket
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- joseph from pittsburgh, PA
- Parts Used:
- WD28X25960
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
bottom rack was rusting away
opened the dishwasher .............removed the old and slid in the new ...then attached by dropping in the utensil compartment.....piece of cake
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- MICHELLE from CHESTERFIELD, NJ
- Parts Used:
- WD28X25960
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The Wheel Was Stuck And It Was Hard To Rolled It
I just ordered another one of the wheel rack and it was that easy. No tool required.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Vivian from Belfast, ME
- Parts Used:
- WD12X10163
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Jet Dry Rinse was not dispensing
Removed 8 screws from inside door cover. Opened the door and pulled off two wires from the detergent rinse dispenser with a pair of pliers and removed screws that held the dispenser in place. Removed the dispenser, placed new part in place and put screws back in and put wires back onto the dispenser. Closed cover and screwed back down. Easiest thing I've ever done.
Was this instruction helpful to you?
Thank you for voting!