PDWT480R30SS General Electric Dishwasher - Instructions

Repairs do not get any easier than this. Remove 12 screws to disassemble door panel (be careful not to let front panel of assembly to drop or bend when screws release it). Remove 6 screws to remove old detergent dispenser. Unplug cable from old dispenser. Connect cable to new dispenser. Install new dispenser into door with 6 screws and then reassemble door panel with 12 screws making sure to keep all wiring free from pressure points.

Removed dish washer from cabinet area and snapped new clip into cable and hook into support.. The time that took the longest was to removed the screws to pull the unit out of the cabinet area.. Very easy fix...

Installed new rack assembly and it works fine. Thanks

Opened dishwasher after it completed a wash cycle. Found the rinse dispenser cap had come off during the wash and melted on the heating coil at the bottom of the machine. Pulled cap off of coil, made sure coil was not disturbed. Looked in various sites for cap. Finally found this site where I didn't need to order the whole mechanism and could order just the cap. Received the cap, screwed into the dispenser, fixed. The only problem I had was that there were two possible caps so I picked the one that was the same color as the original one. Project completed. Thanks

removed original rack, inserted replacement.

Simply took out the broken rack and inserted the new one.

I unscrewed the screws in the door of the dishwasher. Then pulled the inside part of the door up and unscrewed the 6 screws that held the dispenser. I am not sure the correct name of the part but it is on the backside of the dispenser and is red and it is where the wires connect to it, that was probably the most difficult part, disconnecting the plastic covers from the old dispenser. I used a butter knife to pop it out and then was able to get a better grip to pull them off. I pushed the wires on the new red thing and then put the new dispenser in place. You have to make sure that the dispenser is in the right spot and the brace on the underside of the inside part of the door, is in the correct place, otherwise, you will have a leak. Which is what happened to me. I just unscrewed and opened it again and screwed the screws tighter and it was fine.

Removed two pieces on bottom, pulled dishwasher out changed a cable and put it all back together! It was a little plastic piece that broke! Thank you for you quick response! Ordered one day came two days later! Great service!

I began to notice a loud grinding sound when my dishwasher blower motor kicked in (mostly at the end of the entire washing cycle). It was obvious where the noise was coming from (upper left side of door). Ordered blower motor / fan and replaced it. Problem solved! When taking the front panel off, be very aware of all screws. There is a screw on the right side of the door that screws inward. It holds the control unit. If not removed, the control unit screw hole will break off and it will be difficult for you to secure the control unit. Be aware that there are two small screws that point UP below the front panel. Be sure to remove those too. Take pictures of the wires before disconnecting from the control unit. It's fairly obvious, but cheap insurance if needed when reassembling. The fan motor in the upper left of the panel. There are a large gray venting unit above it. You will need to remove that unit in order to expose the screws to remove the fan motor. Once removed, replace the fan motor and work backwards to connect everything again. Possibly take a few moments to clean the inside of your door panel to remove any hard water build up from any moisture that leaked into your door panel. Hope this helps.

bottom installation was extremely easy. top installation required removing the spin piece and reattaching it to the new basket so it was a little more challenging but having the new racks is wonderful! Very quick delivery which was great.

removed inside door panel to access the pump; then replaced with new pump

I disconnected the pipes to the inlet valve. I removed the bolts from the bracket holding the valve. I tried to use two wrenches to remove the brass angle pipe thingie off the bottom of the old valve. I then beat on it with a hammer, then I just threw it against the basement floor till it came off. I would recommend getting a new brass angle pipe thingie before you start.

After reading other customer responses I decided to attempt the repair myself. After pulling out dishwasher I turned it on it's side and prodeeded to remove the 3 screws holding it in place. FIFTEEN minutes later I pushed it back into position and it has performed like new for the past month. Comparing parts and service I saved about $200.00 on this self repair. I would not hesitate to undertake another repair after my experience.

Remove the door panel screws on the inside door frame. You only need to remove as many as needed to remove the larger bottom panel. The other screws will remove the upper button panel and this is not necassary. Unplug the Detergent Dispenser (it may take some force, and unscrew the dispencer. Replace with the new one, screw back in place, and reattatch the plug. Now replace the door panel and screw it back in place. This is all very simple. The only problem I encountered was that the only dispenser had built up so much detergent residue around its base, that it had distorted the plastic around it. This caused the new dispense to not sit flush all the way around, and the dishwasher leaked into the door on its first cycle. Simply filling the gap with 100% silicon caulk has fixed the problem. Washes like new.

Removed the holding screws around the edges; removed and replaced the soap container; reconnected the electrical leads, and done... Very simple fix. But it does get a little tricky since the door is spring loaded. NOTE: THERE ARE SCREWS AT THE BOTTOM THAT IS NOT OBVIOUS.