PDWT400R30WW General Electric Dishwasher - Instructions

Took old one out, put new one in in less than 20 seconds!

Ordered part online, arrived two days later. Removed and replaced dispenser with new unit. Easy job. Dishwasher works like new.

installed new silverware basket

opened the dishwasher .............removed the old and slid in the new ...then attached by dropping in the utensil compartment.....piece of cake

I just ordered another one of the wheel rack and it was that easy. No tool required.

Removed 8 screws from inside door cover. Opened the door and pulled off two wires from the detergent rinse dispenser with a pair of pliers and removed screws that held the dispenser in place. Removed the dispenser, placed new part in place and put screws back in and put wires back onto the dispenser. Closed cover and screwed back down. Easiest thing I've ever done.

Just removed the prior rack and put the new one in. Much improved design on the wheels and rack seems of better material as well. The rack does not have as many holders as the prior rack dishes and pans do not fit as well.

I received the part very quickly. I threw away the old rack and put the new one in it's place. No tools or instructions were necessary. The new rack had all of the wheels and combs included. I did not have to purchase them separately. This is a much better designed part than the original rack. The combs are spread differently to better support plates, and the wheels are combined and enclosed to better support the rack. Also, I feel that this was a good price. Thank you!

I took the old rack out of the dishwasher, took the new one out of the box it was shipped in and slid it into place. Works great. Need top one soon, but will wait until there's some extra money to order it!!!! Thanks for everything!!

Simply screwed in the new rinse aid cap to replace the old one

Middle arm bearing used a pair of pliers to unscrew the screw and to re-screw with new bearing in place. NO did not have to disconnect the arm. Lower arm turn counter clockwise to remove (comes off very easy) stick needle nose straight down opening and remove bearing. Use needle nose to place new bearing.

simply removed broken valve and replaced with new valve, easy peasy. shipping was GREAT, Overnight. all in all a easy fix.

I unscrewed the screws in the door of the dishwasher. Then pulled the inside part of the door up and unscrewed the 6 screws that held the dispenser. I am not sure the correct name of the part but it is on the backside of the dispenser and is red and it is where the wires connect to it, that was probably the most difficult part, disconnecting the plastic covers from the old dispenser. I used a butter knife to pop it out and then was able to get a better grip to pull them off. I pushed the wires on the new red thing and then put the new dispenser in place. You have to make sure that the dispenser is in the right spot and the brace on the underside of the inside part of the door, is in the correct place, otherwise, you will have a leak. Which is what happened to me. I just unscrewed and opened it again and screwed the screws tighter and it was fine.

Removed two pieces on bottom, pulled dishwasher out changed a cable and put it all back together! It was a little plastic piece that broke! Thank you for you quick response! Ordered one day came two days later! Great service!

I began to notice a loud grinding sound when my dishwasher blower motor kicked in (mostly at the end of the entire washing cycle). It was obvious where the noise was coming from (upper left side of door). Ordered blower motor / fan and replaced it. Problem solved! When taking the front panel off, be very aware of all screws. There is a screw on the right side of the door that screws inward. It holds the control unit. If not removed, the control unit screw hole will break off and it will be difficult for you to secure the control unit. Be aware that there are two small screws that point UP below the front panel. Be sure to remove those too. Take pictures of the wires before disconnecting from the control unit. It's fairly obvious, but cheap insurance if needed when reassembling. The fan motor in the upper left of the panel. There are a large gray venting unit above it. You will need to remove that unit in order to expose the screws to remove the fan motor. Once removed, replace the fan motor and work backwards to connect everything again. Possibly take a few moments to clean the inside of your door panel to remove any hard water build up from any moisture that leaked into your door panel. Hope this helps.