PDW7800P00WW General Electric Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Paul from KENT, WA
- Parts Used:
- WD15X10014
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Wrench set
valve leaked
shut off water. removed lower panel disconnected power removed supply hose and outlet hose. disconnected electrical plug from valve. Un bolted valve from frame. removed elbow from valve inlet. installed elbow on new valve using Teflon tape. reinstalled valve to frame. connect hoses + electric plug to new valve. turn water on check for leaks. reconnect power. run dish washer check for leaks & popper operation. reinstall lower panel.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- C. from Lexington, KY
- Parts Used:
- WD01X10175
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Would only drain intermittenly
Thought it might be check flapper valve on drain pump, so I replaced fairly easily, per instructions. When doing, I noticed the attached relay wires were not secure. When it was on the drain cycle one of the relay wires vibrated badly and loosened the connection enough to only work occasionaly. Would like to put new relay on the pump but they do not sell separately from the pump. (one assembly). I resecured connection and will wait till relay gives out and buy new assembly, but for now it's working perfectly!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- robert from HAYMARKET, VA
- Parts Used:
- WD08X10018
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
Leaked front right side
Followed the instructions that came with the my order
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Samuel from LAS VEGAS, NV
- Parts Used:
- WD14X10009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Hinge arm link wore out
Used Phillips screwdriver to undo brackets that keep dishwasher in place. Pulled out dishwasher from underneath the counter. Placed hinge arm in spring, hooked spring onto clip, placed hinge arm in clip. Put back dishwasher under the counter and screwed in place. Took all of 15 minutes. Saved 185.00 for service call.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anna from BRIDGEPORT, WA
- Parts Used:
- WD21X10169
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Dishwasher was stopping mid-cycle and beeping every 15 seconds (as if the door had been opened)
I watched this video: https://www.youtube.com/watch?v=-k0iZGwMOGc
And then I did exactly what it said! It was easy. Plus, when I opened the panel I could see the old switch interlock assembly was melted on one side, so I knew I had gotten the right part!
And then I did exactly what it said! It was easy. Plus, when I opened the panel I could see the old switch interlock assembly was melted on one side, so I knew I had gotten the right part!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from NAPLES, FL
- Parts Used:
- WD08X10075
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Water and soap leaking out the bottom of the door while operating.
I Googled bottom door gasket replacement on GE model and found several videos walking me through the process. I followed one of them and successfully replaced the gasket without pulling the appliance out.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward from AVON, IN
- Parts Used:
- WD12X10163
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Mainly leaking Rince Aid, but occasionally the soap door did not open to dispense soap
Watched the video, and followed the directions. Although my machine had some slight differences, the repair went pretty much per the video. Got all connections back where they belonged, cleaned up the insides a little while had the door parts separated, then buttoned it all back up, ran a cleaning solution thru empty washer, let it dry then started filling with dishes and ran the wash cycle the next day when full. All is well.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Prasad from LEAWOOD, KS
- Parts Used:
- WD21X10169
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
Dishwasher was not starting
Replaced interlock assembly as one of the possible causes. The replacement was easy, but this was not the final fix. I also replaced the water inlet valve, flood switch and finally found that there was large calcification within the drain tube assembly (not visible, but was blocking water). Got a new flexible tubing and new drain hose, plugged everything together and the dishwasher runs like new now. Watching for a potential leak from the drain tube to drain hose connection and mya need to tape it up, but so far so good...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Darrell from DELANO, CA
- Parts Used:
- WD35X20994
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Rollers worn out, top rack would not slide open or closed without wiggling around.
Removed rack, removed old roller pieces, installed new, replaced rack , and works as new now!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- carla from valdosta, GA
- Parts Used:
- WD22X10047
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Food particles had started stopping up spray arm and get them out.
Pulled old spray arm off and snapped new one on. Less than 3 minutes and works great. Dishes are cleaner now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bob from Chandler, AZ
- Parts Used:
- WD28X25960
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Due the the age of this dishwasher (13 years) both upper and lower racks were showing significant rusting.
This lower rack (GE part #WD28X25960) was ready to roll right into the dishwasher straight out of the box, no tools needed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jack D from CLEBURNE, TX
- Parts Used:
- WD22X10047
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Heat shield on lower spray arm came loose and blocked spray arm from turning
Followed instructions on how-to video on website on how to remove and replace lower spray arm.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from FAIRFIELD, CT
- Parts Used:
- WD28X24469
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Holes in old dishwasher basket
The replacement dishwasher basket easily fit in my dishwasher. Easy to order. Quick delivery. Highly recommended.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- M Anne from VIENNA, VA
- Parts Used:
- WD22X10047
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Our dishwasher lower arm had become clogged
HAHA! The easiest repair we have ever done! Took it out of the box, snapped the old arm loose, put the new arm in and -- the dishwasher works like new! Thank you!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ROY G from GAINESVILLE, VA
- Parts Used:
- WD08X10075
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Bottom door seal leaking
Do not overlook the two screws on the bottom of the outer door panel.
Was this instruction helpful to you?
Thank you for voting!