EDW6100N10CC General Electric Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Jack D from CLEBURNE, TX
- Parts Used:
- WD22X10047
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Heat shield on lower spray arm came loose and blocked spray arm from turning
Followed instructions on how-to video on website on how to remove and replace lower spray arm.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- M Anne from VIENNA, VA
- Parts Used:
- WD22X10047
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Our dishwasher lower arm had become clogged
HAHA! The easiest repair we have ever done! Took it out of the box, snapped the old arm loose, put the new arm in and -- the dishwasher works like new! Thank you!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- carla from valdosta, GA
- Parts Used:
- WD22X10047
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Food particles had started stopping up spray arm and get them out.
Pulled old spray arm off and snapped new one on. Less than 3 minutes and works great. Dishes are cleaner now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bob from Chandler, AZ
- Parts Used:
- WD28X25960
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Due the the age of this dishwasher (13 years) both upper and lower racks were showing significant rusting.
This lower rack (GE part #WD28X25960) was ready to roll right into the dishwasher straight out of the box, no tools needed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Darrell from DELANO, CA
- Parts Used:
- WD35X20994
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Rollers worn out, top rack would not slide open or closed without wiggling around.
Removed rack, removed old roller pieces, installed new, replaced rack , and works as new now!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- robert from HAYMARKET, VA
- Parts Used:
- WD08X10018
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
Leaked front right side
Followed the instructions that came with the my order
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michele from NEOLA, UT
- Parts Used:
- WD13X10066
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
its wasn't latching so the dishwasher wouldn't work unless i held the door in the whole time
I called your tech and she sent me a awesome video that made it so easy to fix on my own
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Faye from E STROUDSBURG, PA
- Parts Used:
- WD12X10278
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
old wheels kept falling off
Took stud out of old wheel, put new stud in. It was that easy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from WALNUT CREEK, CA
- Parts Used:
- WD12X10278
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Broken axle which hold wheel on lower rack
Easy install, snap in new axle and put wheel on stud. Be sure to check all wheels for any replacement due to heat melting wheels on rack.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kenneth from Dublin, OH
- Parts Used:
- WD12X10163
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Old soap dispensor latch would not hold
Turned off the power at the main box. Removed the six phillips screws and two bottom hex screws holding the front panel. Removed the two solenoid wires on the old dispenser (Label wire polarity). Removed the eight screws holding the old soap dispensor and took it out. Cleaned the area around the hole. Laid down a bead of silicon caulk around the hole edges. Placed the new dispenser in the hole and replaced the eight screws (do not over tighten). Replaced the two wires on the dispenser solenoid (check polarity). Replaced the front cover (Do not over tighten. Turned on the power and job complete.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- C. from Lexington, KY
- Parts Used:
- WD01X10175
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Would only drain intermittenly
Thought it might be check flapper valve on drain pump, so I replaced fairly easily, per instructions. When doing, I noticed the attached relay wires were not secure. When it was on the drain cycle one of the relay wires vibrated badly and loosened the connection enough to only work occasionaly. Would like to put new relay on the pump but they do not sell separately from the pump. (one assembly). I resecured connection and will wait till relay gives out and buy new assembly, but for now it's working perfectly!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brian from DERRY, PA
- Parts Used:
- WD15X10003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Wrench (Adjustable), Wrench set
Leaking at the valve
Just like the video and replaced it
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ARTHUR from OAK PARK, IL
- Parts Used:
- WD12X10163
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Pliers, Screw drivers
Detergent dispenser did not work
Followed the instruction video on your website. It was accurate and valid. The repair should have taken 15 mins., instead one of the screws holding the dispenser was frozen. Tried DW-40, and liquid wrench. Neither worked because the screw was in plastic.Finally got out the Dremel and cutting wheels. Had to cut away enough of the unit until I could get at the screw (it was the center bottom one). Sliced through some more of the housing, then cut a notch in the screw head deep enough so I could apply enough pressure with a flat blade screwdriver to open it. After that things went as smoothly as could be expected.A bad design and cheap materials.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Everett from FREDERICKSBRG, VA
- Parts Used:
- WD15X10003
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers
No water in
Pulled washer out. Found water inlet valve in lower left. Shut off power and water. Replaced valve with new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JOHN D. from GOSHEN, IN
- Parts Used:
- WD01X10175
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
wouldn't drain
Removed the dishwasher to get at the defective parts and removed,than replaced the two check valves and reassemble.
Was this instruction helpful to you?
Thank you for voting!