GSM2260V00SS General Electric Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Robert from OLD TOWN, FL
- Parts Used:
- WD21X10261
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
No power to dishwasher
Replace both micro switches.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from EDEN PRAIRIE, MN
- Parts Used:
- WD28X31819
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Rear 1/2" wheels on new rack were too narrow causing rack to fall off tracks
Removed 3/4" rear wheels from old damaged rack and installed them on new rack. Works fine now. For the price paid for this replacement rack, wide wheels should be included as part of the replacement package.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Pankaj from KENNESAW, GA
- Parts Used:
- WD09X10024
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The original knob broke off
After aligning the new knob shaft to the slotted hole and with a slight inward pressure, it snapped right in place
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Elizabeth from JONESBOROUGH, TN
- Parts Used:
- WD28X31819
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
NEEDED TO REPLACE LOWER RACK IN DISHWASHER TO SELL HOUSE
TOOK THE RACK OUT OF THE BOX AND PLACED IT IN THE DISHWASHER, DONE.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- john from SOUTHPORT, NC
- Parts Used:
- WD12X10304
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
rack slide end cap broke
Slide it into the arm until you hear it snap
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kathy from LaVergne, TN
- Parts Used:
- WD12X10327
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
one of the rollers was broken away from the rack and when I would pull out the top rack it would sometimes drop downward and the dishes would rattle. I was afraid that it might leave go completely and I would have alot of breakage.
Removed the end tabs from the rack and then removed the rollers one at a time.
Replaced the rollers one at a time , one side at a time, starting with the rear ones. I had to use the pliers to remove one of the rollers ( it was tight) and to dislodge the end cap brackets on the rack.
Replaced the remaining 3 rollers.
Placed the end cap brackets back on the rack and then slid the rack into place.
It works great now!
Replaced the rollers one at a time , one side at a time, starting with the rear ones. I had to use the pliers to remove one of the rollers ( it was tight) and to dislodge the end cap brackets on the rack.
Replaced the remaining 3 rollers.
Placed the end cap brackets back on the rack and then slid the rack into place.
It works great now!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Nashville, NC
- Parts Used:
- WD12X10327
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Two rollers on top rack broke
First, I read several other repair stories on the PartSelect site. The best advice I got was in how to remove the end caps. Another customer described you had to twist them to get them out. One customer had broken the end caps trying to get them out - something I definitely wanted to avoid. I twisted out the end caps, put the new rollers in, snapped them into place, and put the end caps back on. I was done in minutes and (briefly) a hero to the wife, who hates to pay for service calls!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DWIGHT from WOLFEBORO, NH
- Parts Used:
- WD12X10327
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Top drying rack rollers were worn out and needed replacing, rack was falling off slider.
Relatively easy. It took a bit of time to figure how to get the stops out of the end of the slider rack to be able to remove the rack and replace the rollers. I figured out you have to use needle-nose pliers to gently bend the tab on the stop (facing the rear of the diswasher) backwards and then tilting it out. Then the rack rolls right out and the replacement of the rollers was simply a matter of snapping off the old ones off the spindle, and reinstalling the new ones.
You have to be careful you don't break the tabs on the stops on the front of the rails, or you will have a rack that keeps falling out of the front when you pull it out. Be gentle with them and take your time!
Parts Direct was great, by the way, shipping and service was almost immediate! Their supply of parts is amazing!
You have to be careful you don't break the tabs on the stops on the front of the rails, or you will have a rack that keeps falling out of the front when you pull it out. Be gentle with them and take your time!
Parts Direct was great, by the way, shipping and service was almost immediate! Their supply of parts is amazing!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephen from Waterville, ME
- Parts Used:
- WD12X10304
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
PS259168 Replaced broken end cap on upper dish rack
No tools needed for this half-minute repair. Just bend the flexible plastic tab on the back of the end cap until it slips into the metal rail and the end cap snaps into place. Couldn't be easier or simpler!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from Cleveland, TN
- Parts Used:
- WD12X10327
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Roller on rack broken allowing rack to droop below runner.
The biggest challenge is to remove the plastic runner stops without breaking them. I used a small flat blade screw driver to carefully flex back the rear flange of the runner stop so that it would clear the top metal flange of the runner. Then disengage the stop by rotating the body of the stop towards the center of dishwaser tub and this will allow the stop to slide out of the runner flanges. Once the stops are removed it is very simple to remove the rack snap on the new rollers and replace.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from Raleigh, NC
- Parts Used:
- WD12X10327
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Rollers were broken
Just like the other guy's repair:
Took plastic stops off
Replaced rollers
Installed plastic stops
Forgot to make grunting noise to make wife think I'm working hard.
Walked away.
5 mins.
Took plastic stops off
Replaced rollers
Installed plastic stops
Forgot to make grunting noise to make wife think I'm working hard.
Walked away.
5 mins.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Susan from Rochester Mills, PA
- Parts Used:
- WD12X10327
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
broken rollers
First we popped off the end caps to release the rack. We used a pliers and screwdriver. This was the most difficult. The rollers went off and on very easily. We used the pliers to put the end caps on too.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brett from san Leandro, CA
- Parts Used:
- WD12X10327
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
We had a broken roller on the pull out rack.
I removed the end clips on the pull out rack track. took out the broken roller end and snapped the new roller onto the rack and into the track snapped in the end cap. Problem solved !!! Now the wife can get back to work!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kristin from Carlsbad, NM
- Parts Used:
- WD12X10327, WD12X10304
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Rollers were broken and end cap on one side was gone.
I was really suprised at how fast the parts arrived. We used some pliers to open the slide to remove the one end cap still in place. Took what was left of the old roller off and snapped the new ones on slide the rack back into place and replaced the end caps. This was really easy. took no time at all.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- donna from walworth, NY
- Parts Used:
- WD12X10304
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
upper dishwashr rack lost the end cap and the rack kept coming off the track when you went to push it back in it would jam into the track and all the dishes would bang and fall.
placed the end cap into location and forced it into place. Fixed -and we are all much happier!!
Was this instruction helpful to you?
Thank you for voting!