GDWT100R30BB General Electric Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Alice from BLAINE, MN
- Parts Used:
- WD12X10122
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
cap had melted mi
Unscrew the old one and screw in the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jimmy G from SPRING, TX
- Parts Used:
- WD15X10014
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
Water leakage at valve
I watched the video that came with email on part. Gave instructions on how to. Thank you !
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Harinder from CHESTERFIELD, NJ
- Parts Used:
- WD12X10163
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
detergent dispenser was not closing and dishes were dirty
followed the video step by step which was very well expalined and was able to complete the install
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DENNIS from MAUMEE, OH
- Parts Used:
- WD12X10163
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Rinse cap was broken
Watched online video, repaired myself in under 10 minutes.
Easy fix with video instructions
Easy fix with video instructions
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marilyn from CALDWELL, ID
- Parts Used:
- WD35X21041
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Needed to replace rollers on bottom dishwasher rack
Pulled off old rollers and snapped on new ones. Never easier!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- REVERIE from HAMPTON, VA
- Parts Used:
- WD35X21041
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
lower rack wheels kept falling off
delivery of part was very quick, and my husband was able to remove the old part and install the new in about 10 minutes. No service call; no new rack; just a washer that is easy to use again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Melissa from WARNER ROBINS, GA
- Parts Used:
- WD35X21041
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Dishwasher not cleaning properly
The kit came with the anchors and the riollers for the bottom shelf. They clipped right on! Dishwasher cleans great now!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lisa from CHARLOTTE, NC
- Parts Used:
- WD35X21041
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The rollers on the bottom rack of my GE Monogram Dishwasher all broke and melted so opening and closing the rack was extremely difficult!
It couldn't have been easier. I installed the new wheels in seconds and the rack glides as perfectly as the day it was installed 11 years ago! Perfection! Your stellar website made it so easy to find the correct parts. BRAVO!!!!! I laughed! I cried! I am so ECSTATIC!!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from JONESBOROUGH, TN
- Parts Used:
- WD15X10014
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Wrench (Adjustable)
Would not fill with water
Ordered most likely part...water inlet valve.
1. Turn off water supply.
2. Remove the metal toe kick plate/insulation at the bottom of the
dishwasher.
3. Remove hose to supply valve.
4. Take electrical plug off old valve.
5. Remove float valve because it was mounted it right in the way of
the 2 screws on the inlet valve bracket.
6. Remove those 2 screws now you can get to them, and move the
inlet valve to one side so you can get to the hose clamp for the
rubber hose out of the valve going to the dishwasher.
7, Take the old valve and bracket out, mount new valve on the
bracket, crawl back down on the floor, reinstall rubber hose and
bracket, and float valve and finally inlet hose.
8. Turn water on. Check hose connections for leaks. Yep, outlet
hose didn't clamp enough now, allowing a drip.
9. Repeat the whole process AGAIN. Replace little clamp
with a REAL hose clamp, reinstall the thing again. No leak this
time.
10. Test run dishwasher thru a cycle. Check again for leaks at hose
connections. OK ? Reinstall insulation pieces and toe kick
plate.
1. Turn off water supply.
2. Remove the metal toe kick plate/insulation at the bottom of the
dishwasher.
3. Remove hose to supply valve.
4. Take electrical plug off old valve.
5. Remove float valve because it was mounted it right in the way of
the 2 screws on the inlet valve bracket.
6. Remove those 2 screws now you can get to them, and move the
inlet valve to one side so you can get to the hose clamp for the
rubber hose out of the valve going to the dishwasher.
7, Take the old valve and bracket out, mount new valve on the
bracket, crawl back down on the floor, reinstall rubber hose and
bracket, and float valve and finally inlet hose.
8. Turn water on. Check hose connections for leaks. Yep, outlet
hose didn't clamp enough now, allowing a drip.
9. Repeat the whole process AGAIN. Replace little clamp
with a REAL hose clamp, reinstall the thing again. No leak this
time.
10. Test run dishwasher thru a cycle. Check again for leaks at hose
connections. OK ? Reinstall insulation pieces and toe kick
plate.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anthony from East Islip, NY
- Parts Used:
- WD18X10026, WD18X10010
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Socket set, Wrench set
Water leaking underneath dishwasher
went online to parts select. Looked at parts that could be leaking. Thought it was the sump. Purchased the sump and the pump connector. Almost bought the adaptor pump assembly, but it was $29.00. Parts arrived in about 2 days. Turned off water and power to dishwasher. Disconnected the copper water line. Hardest part was getting the dishwasher out of space. Once out, layed it on it's side. Parts held together with clamps. Took it apart like a puzzle. Replaced the parts, tightened the clamps. Pump connector hard to unscrew. Got a good hand grip on it and turned it loose. Sump did have a hole in it. Put everything back together. water, electric, etc. Turned it on and it was leaking. Leak coming from the adaptor pump assembly. Couldn't wait 2 more days.Found part at a local parts store for $40.00. Was able to change it by reaching underneath and not pulling dishwasher out again. All three parts needed to be changed. Dishwasher now working fine. If your leaking underneath and taking out the dishwasher change those 3 parts.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from Cincinnati, OH
- Parts Used:
- WD30X10020, WD12X10184
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
ball bearings falling out of the upper dish rack
pulled the end caps, pulled the upper dish rack out. Installed the rear end cap on the right hand side of the inside slider for the rack. installed the bearing and slider in position. Put the upper rack back in and installed the front end caps.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Scott from pleasanton, CA
- Parts Used:
- WD28X10410, WD28X25960
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Wire basket rusting.
The Lower Rack was a simple swap. The Upper Rack had a tube and rotating sprayer that had to be removed and installed on the new rack. I used a nutdriver to remove a few screws and reinstall them on the new unit. Very simple.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- tim from prior lake, MN
- Parts Used:
- WD12X10163
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The soap dispenser would not close.
This was simple. I took the door apart with a portable screw driver. Then I detached the wires and unscrewed the old module and replaced it. I then put the door back together, loaded the dishwasher and it cleaned my dishes. Even for this `old dog' it was easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Amelia from PEORIA, IL
- Parts Used:
- WD28X25960
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Rack was rusted and broken.
It was a very simple replacement. I took the old one out and rolled the new one in. It took less than 5 minutes!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jean from White Plains, NY
- Parts Used:
- WD12X10122
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
missing cap
I placed the missing cap into the dispenser.
Was this instruction helpful to you?
Thank you for voting!